EasyManuals Logo

Epson PowerLite 955W Operation Guide

Epson PowerLite 955W
85 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #50 background imageLoading...
Page #50 background image
Set the computer, the access point, and the projector to the same SSID.
Go to Network > Network Configuration > Wireless LAN > SSID.
Set DHCP to Off. When DHCP is set to On, it may take some time to enter LAN standby status if an
available DHCP server is not found.
Go to Network > Network Configuration > Wireless LAN > DHCP or Network > Network
Configuration > Wireless LAN > IP Settings > DHCP.
Set the IP address, the subnet mask, and the gateway address for the projector correctly.
Set Wireless LAN Power to On.
Go to Network > Network Configuration > Wireless LAN > Wireless LAN Power.
Set the wireless LAN system to meet the standards supported by the access point.
Go to Network > Network Configuration > Wireless LAN > Wireless LAN system or Wireless
LAN Sys.
When you enable the security setting, set the same passphrase to the access point, the computer,
and the projector.
Close network settings on the projector, and then return to the LAN standby screen.
Check the computer's network settings.
If the wireless LAN adapter is not installed on your computer, install a wireless LAN card on your
computer.
Enable the wireless LAN setting or AirPort on your computer.
Connect to the access point to which the projector is connected.
Turn off the firewall. If you do not want to turn it off, register the firewall as an exception. Make the
necessary settings to open the ports. The ports used by this software are "3620", "3621", and
"3629".
Check the access point settings.
Set connection permission at the access point to allow projectors to connect if any functions that
block connections, such as MAC Address restrictions and port restrictions, are set to the access
point.
Check the software settings.
Select the network adapter you are using from Switch LAN on the Set options screen. If the
computer has multiple LAN environments, a connection cannot be established unless the network
adapter is selected correctly.
50

Table of Contents

Other manuals for Epson PowerLite 955W

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Epson PowerLite 955W and is the answer not in the manual?

Epson PowerLite 955W Specifications

General IconGeneral
Number of colors1.073 billion colors
Native aspect ratio16:10
Projection distance0.84 - 8.4 m
Projection technology3LCD
Contrast ratio (typical)10000:1
Screen size compatibility29 - 280 \
Projector native resolutionWXGA (1280x800)
Keystone correction, horizontal-30 - 30 °
FocusManual
Throw ratio1.38 - 2.24:1
Zoom capabilityYes
Focal length range18.2 - 29.2 mm
Aperture range (F-F)1.51 - 1.99
Lamp typeUHE
Lamp power200 W
Lamps quantity1 lamp(s)
Light source typeLamp
Service life of light source5000 h
Service life of light source (economic mode)6000 h
3D-
Full HDNo
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions1280 x 960, 1366 x 768, 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1400 x 1050 (SXGA+), 1440 x 900 (WXGA+), 1600 x 1200 (UXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Composite video in0
USB connector typeUSB Type-A, USB Type-B
Serial interface typeRS-232
USB 2.0 ports quantity2
VGA (D-Sub) ports quantity3
Noise level37 dB
Noise level (economic mode)29 dB
RMS rated power16 W
PlacementDesktop, Ceiling
Product typeStandard throw projector
Product colorWhite
Cable lock slot typeKensington
Power sourceAC
AC input voltage100 - 240 V
Voltage tolerance10 %
AC input frequency50 - 60 Hz
Power consumption (standby)3 W
Power consumption (typical)299 W
Power consumption (PowerSave)221 W
Operating temperature (T-T)5 - 35 °C
Cables includedAC, VGA
Remote control typeIR
Sustainability certificatesRoHS
Weight and Dimensions IconWeight and Dimensions
Depth271 mm
Width294 mm
Height89 mm
Weight2900 g

Related product manuals