Epson WorkForce 435 Quick Setup Instructions

Start Here
3 Squeeze the edge guide as you slide it all the way to the
left.
4 Load letter- or A4-size paper against the right edge and
behind the tab, with the printable side face up.
5 Slide the edge guide over.
6
Connect the phone cord
To fax, connect a phone cord to a telephone wall jack and
to the LINE port on your product. To connect a telephone or
answering machine, use the EXT. port on your product. See
the Quick Guide for more details.
Note: If you’re connecting to a DSL phone line, you must use a DSL
filter or you won’t be able to fax. Contact your DSL provider for the
necessary filter.
Read these instructions before using your product.
1
Unpack
French control panel stickers
(included for Canada only)
Caution: Do not open ink cartridge packages until you are ready to
install the ink. Cartridges are vacuum packed to maintain reliability.
Remove all protective materials.
2
Turn on
1 Connect the power cable.
Caution: Do not connect to your computer yet.
2 Press the On button.
3
Select settings
1 To select English as your language, press OK.
(If you want to change the language, press or to
select it, then press OK.)
2 Select your Country/Region and press OK.
3 Select the current Daylight Saving Time setting (Winter
or Summer) and press OK.
4 Select the Date format and press OK.
5 Press the number keys to enter the Date and press OK.
6 Select the Time format (12h or 24h) and press OK.
7 Press the number keys to enter the Time. Then press
or to select AM or PM, if necessary.
8 Press OK.
4
Install ink cartridges
Note: Do not load paper yet.
1 Lift up the scanner.
2 Open the cartridge cover.
3 Shake the ink cartridges gently 4 or 5 times, then unpack
them.
4 Remove only the yellow tape from each cartridge.
Caution: Don’t remove any other seals or the cartridges may
leak.
5 Insert the cartridges in the holder for each color.
6 Press each cartridge down until it clicks.
7 Close the cartridge cover. Press down until it clicks.
8 Lower the scanner.
9 Press the OK button to prime the printer.
Priming takes about 3 minutes.
Note: Your printer ships with full cartridges and part of the ink
from the first cartridges is used for priming the printer.
Caution: Don’t turn off the printer while it is priming or you’ll
waste ink.
5
Load paper
1 Open the paper support and pull up the extensions.
2 Pull out the output tray extensions and raise the stopper.
*412081000*
*412081000*
WorkForce
®
435

Epson WorkForce 435 Specifications

Print Specifications

maximum print resolution	5760 x 1440 optimized dpi
black print speed	6.3 ISO ppm
color print speed	3.3 ISO ppm

Scan Specifications

optical resolution	2400 dpi
hardware resolution	1200 x 2400 dpi
maximum resolution	9600 x 9600 dpi interpolated

Fax Specifications

fax modem speed	33.6 Kbps
fax memory	up to 180 pages
speed dials	60 max

Operating Environment

operating temperature	50 ° to 95 °F (10 ° to 35 °C)
storage temperature	-4 ° to 104 °F (-20 ° to 40 °C)
operating relative humidity	20 – 80%

Power Specifications

rated voltage	AC 100 – 120 V / 220 – 240 V
rated frequency	50 – 60 Hz
rated current	0.6 Amp

Weight and Dimensions

printing dimensions	18.1" x 21.3" x 11.9"
storage dimensions	18.1" x 16.2" x 9.3"
weight	15.7 lb