28
NOTE: The safety valve is a pressure limiting valve. When the trigger
lever (17a) is released, the valve opens and discharges the pressure
inside the pump.
NOTE: The automatic motor start-stop device is operated by the trigger
lever (17a) of the trigger gun (17). When the trigger lever (17a) is released
the dynamic pressure automatically cuts out the motor. When the trigger
lever (17a) is depressed the automatic drop in pressure starts the motor
and the pressure is restored after a very slight delay.
• Check the machine, its supply cord with plug (6) as well as the accessories for
damage before each use. Do not use the machine if it is damaged or shows
wear.
• Doublecheckthattheaccessoriesandattachmentsareproperlyxed.
• Always hold the trigger gun (17) with both hands,
• Ensure that the air vents are always unobstructed and clear. Clean them if
necessary with a soft brush. Blocked air vents may lead to overheating and
damage the machine.
• Switch the machine off immediately if you are disturbed while working by other
people entering the working area. Always let the machine come to complete stop
before averting.
• Do not overwork yourself. Take regular breaks to ensure you can concentrate on
the work and have full control over the machine.
01
Starting
WARNING! Beware of kickback when squeezing the trigger!
NOTE:
The trigger gun (17) is equipped with a trigger lock lever (17d)
(Fig. 21)
to prevent accidental activation of the trigger lever (17a).
Flip the
trigger lock lever (17d) up before the trigger lever (17a) can be squeezed.
NOTE: Always keep a reasonable distance between the nozzle and the
object to be cleaned in order to avoid damage. Ask your specialist dealer
for advice if required.
1. Connect the machine to a suitable water supply as described.
2. Connect the machine to a suitable socket-outlet as described.
3. Turn on the water tap fully.
5063022018892-EBPW3000-PressureWasher-UM-V03.indd 285063022018892-EBPW3000-PressureWasher-UM-V03.indd 28 09-11-2022 14:09:0709-11-2022 14:09:07
29
4. Holding the trigger gun (17) with two hands, direct the nozzle away from yourself
towards the surface to be cleaned (Fig. 20).
5. Squeeze the trigger lever (17a)(Fig.21)untilwaterowsfromthewateroutlet(21)
without air bubbles.
6. Set the on/off switch (12) to I position (Fig. 16).
7. Change the operating mode by turning the pressure adjustment knob (17c) on the
trigger gun (17) (Fig. 22).
> Turnthepressureadjustmentknob(17c)clockwiseforSOFTmo deoperation.
> Turnthepressureadjustmentknob(17c)anti-clockwiseforHARDmode
operation.
02
After use
1. Release the trigger lever (17a) (Fig. 23, step 1).
2. Set the on/off switch (12) to O position (Fig. 23, step 2).
3. Turn the water supply off (Fig. 23, step 3).
4. Squeeze the trigger lever (17a) to allow all water comes out from the machine and
release the pressure still present in the product (Fig. 23, step 4). Flip the trigger
lock lever (17d) down on the trigger lever (17a).
WARNING!
Only detach the high pressure hose (13) from the trigger
gun (17) and the garden hose from the
water inlet (11)
when no more
pressure exists in the system! Ensure that the machine is switched off
and unplugged.
NOTE:
The trigger gun (17) is equipped with a trigger lock lever (17d)
(Fig. 21)
to prevent accidental activation of the trigger lever (17a). After
use,
ipthetriggerlocklever(17d)downonthetriggerlever(17a).
5. Disconnect the power plug (6) from the socket-outlet.
6. Detach the garden hose from the water supply and then from the water inlet hose
adaptor (19).
7. Detach the high pressure hose (13) from the trigger gun (17).
8. Wind the high pressure hose (13) onto the hose reel (14). Do not bend or twist the
high pressure hose (13).
9. Detach the accessories in the reverse sequence of the assembly instructions.
5063022018892-EBPW3000-PressureWasher-UM-V03.indd 295063022018892-EBPW3000-PressureWasher-UM-V03.indd 29 09-11-2022 14:09:0809-11-2022 14:09:08
96456_IM_Erbauer 3000_EU.indb 2896456_IM_Erbauer 3000_EU.indb 28 2023/3/27 上午11:082023/3/27 上午11:08
To Next Page
Loading...
