Maintenance
Periodically carry out visual inspections to make
sure that no obvious damage has occurred to the E1
device.
Disconnect the E1 device from the electrical supply
and contact your service provider if any of the
following conditions are detected:
• Failure to function as expected
• Noticeable signs of overheating
• Signs of deterioration of the insulation on
electrical conductors
• Damage is found to the power cable or connector
• Liquid has been spilled onto, or an object has
fallen into, the E1 device
• The E1 device has been exposed to water or other
abnormal contamination
Power supply warning
The power supply is for indoor use only. The
equipment power supply cord shall be connected to a
socket-outlet with earthing connection. Only use the
power supply included with the E1 device. Operation
from voltages other than those indicated may cause
irreversible damage to the E1 device and void the
device warranty. If you are unsure of the correct
operational voltage, please contact the company
from whom you purchased or received the E1 device.
Do not attempt to repair or use a damaged
power supply.
Do not immerse the power supply in water or subject
it to physical abuse.
Installation & placement
Verify the E1 device has not been dropped, altered,
transported or shipped without proper packaging, or
otherwise treated without care before installing
the device.
Do not install (or use) the E1 device on an unstable
surface. The E1 device may fall, causing serious bodily
injury and serious damage to the device.
Do not place objects on the E1 device after installa-
tion. Place the E1 device near a main power supply
outlet and make sure that you can easily access the
power breaker switch.
Avoid smoke and dust. Do not use in smoky or dusty
locations. Smoke and dust can damage the E1 device.
Place the E1 device on a at and even surface.
The E1 device should not be placed close to other
pieces of equipment that produce heat or located
such that it is subject to direct sun light.
Do not use the E1 device in places which are
extremely hot, cold, dusty or humid.
Do not place the E1 device or power supply on a bed,
sofa, or other soft surface that may block openings.
Do not remove the E1 device outer plastic enclosure
during normal use.
The E1 device internal USB port is intended for air
mouse receiver connection purpose.
Operation
Do not block any ventilation openings on the E1
device or power supply.
Slots and openings in the E1 device are for ventilation
and must never be blocked or covered since they
ensure reliable operation of the device itself and
protect it from overheating.
Do not restrict the air-ow of the E1 device by placing
it in a place with poor ventilation, by covering it with a
cloth or by placing it on a carpet.
Do not place the E1 device or power supply in a
conned space, such as a bookcase, rack, or stereo
cabinet, unless the space is well ventilated.
Use only the manufacturer supplied AC adapter
approved for use with the E1 device. Use of another
AC adapter may change the compliance of the E1
device and may present risk of re or electric shock.
Any part of the user’s body, other than the hands,
should be kept at a distance of 35 cm or more away
from the E1 device during installation.
All operational modes of AI board: 2.4GHz: 802.11b,
802.11g, 802.11n (HT20), Zigbee
The frequency and the maximum transmitted power
in EU are listed below:
2412-2472MHz: 17.48 dBm
2405-2480MHz: 13 dBm
All operational modes: 2.4GHz, 802.11bgn+ BT, 5GHz
2412-2472MHz : 19 dBm
5180-5825MHz : 20.3dBm.
The E1 device contains an internal, rechargeable
battery that is not replaceable. Do not attempt to
replace the battery. Replacing batteries incorrectly
may increase the risk of re or chemical burns to skin
and eyes.
Do not disassemble, damage, modify, or expose
batteries to conducting materials, moisture, liquid,
or heat. Always discard batteries according to local
laws. In most cases that will be in a waste bin for
electronic devices.
Keep batteries away from children.
Battery warning
The E1 device’s cables and cords present tripping
and entanglement hazards. They should be
organized neatly to reduce the risk of tripping and
entanglement, which can lead to injury to persons
and property. Avoid placing cables and cords in
frequently used locations where children or pets
might play. Do not allow children or pets to play with
cables or cords.
The cables and cords can also present risk of re
or electric shock. Never pull on the power cable
to disconnect the E1 device as this can damage
the power cable. Do not abuse the power cable by
bending, pinching, or knotting the power cable or by
exposing it to heat.
Unplug the E1 device when there is a lightning storm
or when it is unused for extended periods.
If a power cable becomes damaged, stop using it
immediately.
Cables and cords warning
To Next Page
Loading...
Need help?
General
