Erreka SMART-D201m - User Manual

7
SMART-D201(M)
Quick installation and programming guide English
IMPORTANT
NOTE
This quick guide is a summary of the complete installation guide. The guide contains safety warnings and other
explanations that must be taken into account. The most recent versions of this guide and the installation manual
are available at the "Downloads" section on Erreka's website.
http://www.erreka-automation.com
The options and functions described in this guide apply for the firmware version indicated on the circuit. The
firmware, as part of a process of continuous improvement, is subject to new functionalities or upgrades being
included as a result of new versions which are not necessarily compatible with previous ones. For this reason,
some options or functions may differ or be unavailable if your firmware is older than shown in this guide.
E307A
2 x 1mm
2
Electrical cables
A: Main power supply
B/F: Flashing light with antenna
C: Photocells (Rx/Tx)
D: Pushbutton/key switch
E:Operator
Elements of the complete installation
NOTE: this control panel is valid for swing
gate operators, for example:
• TEMIS (no encoder or limit switches)
• KAIROS (with or without limit switches)
• ARES 24V
VERY IMPORTANT: the TC closing stopper and
the TA opening stoppers must be installed.
M2-M1-
Lat-
Lit-
Lmt4Lmt3
Lmt2
Lit+ SKey
S1
M2+
M1+Lat+ Ph2Ph1 PhVcc PhVcc
S25V
ANT
GND
DKey GND
GND
GND
GND
Lmt1
GND
J5
J4 J3
J7
J8
COCOCOCO
12345678 9101112131415161718
19 20 21 22 23 24 25 26
LED3
LED4
LED2
FLASH
A.P.
A.T.
EC
(24VDC)
P307Z
DIP1
DEST (LUMI)
FT2
(FT06)
FT1
(FT06)
Peripheral cabling (valid for all cases)
ANT Cable connectors for antenna
EC Electrolock 24 VDC
A.T. Double-leaf opening pushbutton
A.P. Single-leaf opening pushbutton
DEST Flashing light
(ERREKA LUMI)
Configure DIP1 as shown in
figure
FT1 Exterior safety device (ERREKA
FT06 photocell)
FT2 Interior safety device (ERREKA
FT06 photocell)
MSA-114/05 – 2019-09-19 firmware V1.1 or later

Summary

Elements of the complete installation

Electrical cables

Details the main power, flashing light, photocells, and pushbutton connections.

Peripheral cabling

Describes the connections for antenna, electrolock, pushbuttons, and safety devices.

Operator electrical connections with limit switches (KAIROS)

Operator electrical connections without encoder or limit switches (TEMIS)

Electricity connection

Battery connection (BAT)

Display indications, LEDs and pushbuttons

Selecting the number of leaves (parameter F 1)

Radio code programming (Roller Code transmitters)

Deleting all the transmitters

Programming open;close

Complete programming chart

F1 Encoder; Limit switches

Configures operator encoder or limit switch usage for different models.

F2 Number of operators

Sets the number of operators, for single or double leaf gates.

F3 Maximum trapping current

Defines the maximum current for operator trapping force adjustment.

F4 Gate speed

Sets the operational speed of the gate, expressed as a percentage.

F5 Slowdown

Configures the gate's slowdown behavior during opening and closing.

F6 Slowdown speed

Adjusts the speed at which the gate slows down before reaching limits.

F7 Lapse between leaves

Sets the time delay between the movement of leaves in dual-leaf systems.

F8 Automatic or step-by-step operation

Defines gate operation mode and standby time for automatic functions.

F9 Functions of FT1-FT2

Configures the behavior of exterior (FT1) and interior (FT2) photocells.

Erreka SMART-D201m Specifications

General

Brand	Erreka
Model	SMART-D201m
Category	Control Unit
Language	English