If you do not have ControlSystem
the system can work just as well manually.
Ignore the a
ctivation and calibration operations, switch
to Manual mode and then connect the
4.5 Changing the
ControlSystem
If it is necessary to replace the
system that is already linked, you will need to delete
the old serial number be
fore linking the new one.
To do this, with the SilenPlus
power supply, keep the F
button pressed down for 10
seconds. Flashing LEDs indicate that the operation
has been carried out correctly.
The previous serial number will be deleted
system will go into “link standby” mode. Proceed as
indicated in 4.2.2.
5. OPERATION
5.1 REMOTE mode
This is the default operating mode.
The pump carries out the most appropriate function
considering the position of the filter valve. (See figure
3)
In FILTRATION position:
• In BACKWASH position:
•
In CLOSED position: pump stopped.
•
In any of the other positions: the pump operates at
100% power.
•
When you operate the valve control, the pump
stops automatic
ally to make the valve movement
easier.
•
In any intermediate position, the pump remains
stopped.
To change the working mode, simply move the valve
to the desired position.
To prevent accidental operation, the electronic
response is delayed by 1 second. The
red LED indicates that proper communication
has been achieved.
Move the valve gently.
WARNING: the valve configuration must correspond
to the 6 standard positions, according to figure 3.
For other valve configurations, contact your technical
service.
5.2 MANUAL mode
When you press the M, key SilenPlus
trolSystem
signal and runs one of the preset functions:
The MAN LED comes on.
The pump starts up at a fixed, programmable speed.
The standard setting is 2,300 RPM (40 Hz). This is
what
is known as the MIXED CYCLE (MISC. CYCLE).
If you press the F
key, it runs through the various
SilenPlus functions in sequence.
the system can work just as well manually.
ctivation and calibration operations, switch
to Manual mode and then connect the
SilenPlus.
in a
system that is already linked, you will need to delete
fore linking the new one.
button pressed down for 10
seconds. Flashing LEDs indicate that the operation
The previous serial number will be deleted
and the
system will go into “link standby” mode. Proceed as
The pump carries out the most appropriate function
considering the position of the filter valve. (See figure
function
Plus function
In CLOSED position: pump stopped.
In any of the other positions: the pump operates at
When you operate the valve control, the pump
ally to make the valve movement
In any intermediate position, the pump remains
To change the working mode, simply move the valve
To prevent accidental operation, the electronic
response is delayed by 1 second. The
flashing
red LED indicates that proper communication
WARNING: the valve configuration must correspond
to the 6 standard positions, according to figure 3.
For other valve configurations, contact your technical
Con-
signal and runs one of the preset functions:
The pump starts up at a fixed, programmable speed.
The standard setting is 2,300 RPM (40 Hz). This is
is known as the MIXED CYCLE (MISC. CYCLE).
key, it runs through the various
Between each function, the pump stops to allow valve
movement or other operations.
The sequence is:
1.
Mixed cycle (MISC. CYCLE).
2. Stop.
3. Filtration Plus.
4. Stop.
5. Backwash Plus.
6. Stop.
7. Mixed cycle...
The lit LEDs indicates the function selected at all
times.
When you press the M
button again, you leave Ma
ual mode to go back to Remote.
5.3 No water fault and retries.
In Filtration Plus
mode, the system is regularly mon
tored to check that the pump is not operating without
water.
If SilenPlus
detects the pump is working without water
it stops the motor.
The system will attempt to start up again after 1', 5',
15' and 1 hour (Fig. 4). If th
remain in permanent fault mode.
An LED sequence indicates the fault status. (See fi
ure 7)
To interrupt the retry cycle or to restart from perm
nent fault mode, press the
5.4 System status
Espa offers installers and us
plication for monitoring the system status and
interacting with SilenPlus.
You need to have an Android device with Blu
available from
With this
app, it is possible to switch between
ual/Remote
modes and use all functions.
6. ADVANCED CONFIGURATION
Different speeds can be set to adjust the functions to
the characteristics of the installation.
The function being run will be configured.
To confi
gure a function, first select it, either in Manual
or Remote mode, and at the same time press
for 5 seconds.
All the speeds of the selected function will return to
the factory settings [= fs]
To increase or decrease the speed, press M or F:
M = + 58 RPM (+
F = - 58 RPM (-
• Configuring
The filtration speed is set.
· Minimum = 1,600 RPM (20 Hz), [= fs]
· Maximum = 2,900 RPM (50 Hz), [= fs]
EN
Between each function, the pump stops to allow valve
movement or other operations.
Mixed cycle (MISC. CYCLE).
The lit LEDs indicates the function selected at all
button again, you leave Ma
n-
ual mode to go back to Remote.
5.3 No water fault and retries.
mode, the system is regularly mon
i-
tored to check that the pump is not operating without
detects the pump is working without water
The system will attempt to start up again after 1', 5',
15' and 1 hour (Fig. 4). If th
e retries fail, Evopool will
remain in permanent fault mode.
An LED sequence indicates the fault status. (See fi
g-
To interrupt the retry cycle or to restart from perm
a-
key.
Espa offers installers and us
ers the EspaEvopool ap-
plication for monitoring the system status and
You need to have an Android device with Blu
e-
the EspaEvopool app
app, it is possible to switch between
Man-
modes and use all functions.
6. ADVANCED CONFIGURATION
Different speeds can be set to adjust the functions to
the characteristics of the installation.
The function being run will be configured.
gure a function, first select it, either in Manual
or Remote mode, and at the same time press
M + F
All the speeds of the selected function will return to
To increase or decrease the speed, press M or F:
.
The filtration speed is set.
· Minimum = 1,600 RPM (20 Hz), [= fs]
· Maximum = 2,900 RPM (50 Hz), [= fs]
To Next Page
Loading...