ETC
®
Setup Guide
Congo
™
Radio Remote Focus Unit (cRRFU)
cRRFU Setup Guide Page 1 of 5 Electronic Theatre Controls, Inc.
Corporate Headquarters
3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA
Tel +608 831 4116
Fax +608 836 1736
London, UK
Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK
Tel +44 (0)20 8896 1000
Fax +44 (0)20 8896 2000
Rome, IT
Via Ennio Quirino Visconti, 11, 00193 Rome, Italy
Tel +39 (06) 32 111 683
Fax +44 (0) 20 8752 8486
Holzkirchen, DE
Ohmstrasse 3, 83607 Holzkirchen, Germany
Tel +49 (80 24) 47 00-0
Fax +49 (80 24) 47 00-3 00
Hong Kong
Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong
Tel +852 2799 1220
Fax +852 2799 9325
Service:
(Americas) service@etcconnect.com
(UK) service@etceurope.com
(DE) techserv-hoki@etcetcconnect.com.com
(Asia) service@etcasia.com
Web:
www.etcconnect.com
Copyright © 2007 ETC. All Rights Reserved.
Product information and specifications subject to change.
7310M2200
Rev D
Released 01/2009
Overview
The Congo Radio Remote Focus Unit (cRRFU) provides a simple, wireless solution for remote control.
Compatible with the ETC Congo and Congo jr consoles, this small hand-held transmitter unit provides
access to frequently used commands for dimmer and channel checks as well as update and record
functions. The small receiver unit plugs directly into and is powered by a USB port on the console or
through a powered USB hub.
Installation Instructions
The receiver unit is provided with a chassis USB connector and connects via a supplied 1.8m USB
cable to the console. The maximum distance is 5m between receiver and console (hub).
If you need to deploy the receiver further away from the console,
please look for our RFR Advanced Radio Remote Unit that is
based on Ethernet.
The transmitter unit requires a single 9V alkaline battery (provided)
for power. This battery should provide approximately one year of
normal usage before requiring replacement. To replace the battery,
remove the two M3x4mm screws at the bottom of the unit to
access the battery compartment and replace with a 9V alkaline
battery. Replace the lid and secure it with the same two screws.
Dispose of the old battery as is appropriate in your local area.
Transmitter Setup
The transmitter unit has a slide switch (on/off) and 16 keys for
console commands. The unit has a “sleep” feature that helps to
conserve battery life when the switch is left in the “on” position. Set
the switch to the “off” position to guard against accidental key
presses.
The keys of the transmitter unit are illuminated. The keys are
brightly lit while keys are pressed and the unit is transmitting. After
the key is released, the keys remain dimly lit for a period of time
before the unit sleeps. The sleep delay can be programmed at the
transmitter unit as described below.
Note:
If multiple units are to be used separately within range of each other’s receiver
units, please refer to Page 4 for modification of the communication encoding.
C
0 %
Update
1
Preset
4
7
2
5
8
100%
3
6
9
0
Record
Go / Goto
.
Thru
Func
@ Level
Group
Check+Check-
Ch
Go Back
- % + %
+
-
All
To Next Page
Need help?
General
