A
A
A
B
B
A
1. Locate two stabilizer tubes A and one pylon B.
Turn the pylon B upside down and insert one end of each
stabilizer tube A into the bottom of the pylon B, as shown.
Make sure both stabilizer tubes are fully inserted into
the bottom of the pylon.
1
(1) Hardware Kit Bag
1 Instructions
3 8-16 x 75 mm Screws
15 8-16 x 18 mm Screws
(1) Toy Kit Bag
6 Bags of Toys
WARNING
Warnings .............................................................................................................................................. 1
Assembling the ExerSaucer .................................................................................................................... 1
Attaching the Toys ................................................................................................................................. 5
Adjusting the Height ............................................................................................................................. 6
Care and Maintenance ............................................................................................................................ 6
Limited Warranty .................................................................................................................................... 7
Table of Contents
Tray
Seat Pad
Wheel (4)
Pylon (3)
Seat Ring
Stabilizer Tube (3)
Assembling the ExerSaucer
8-16 X 75 mm Screw (3)
8-16 X 18 mm Screw (12)
Foot (3)
Base
READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS! FAILURE TO DO SO COULD RESULT
IN SERIOUS INJURY OR DEATH!
• NEVER leave child unattended. ALWAYS keep child in view while in the ExerSaucer®.
• Read all instructions before assembly and use of the ExerSaucer.
• Keep instructions for future use.
• Keep children away from unassembled product.
• Adult assembly required. Take care when unpacking and assembling; contains small parts and some items with sharp edges.
• To prevent a possible choking hazard, remove and immediately discard packing material before using this product.
• STRINGS CAN CAUSE STRANGULATION!
- DO NOT place the ExerSaucer anywhere near cords from window blinds, draperies, phone, etc.
- DO NOT place items with a string around your child’s neck such as hood strings or pacifier cords.
- DO NOT suspend strings over product or attach strings to toys.
• NEVER use ExerSaucer near stairs or steps.
• NEVER use ExerSaucer near ranges, radiators, space heaters, and fireplaces or any other hot surfaces.
• NEVER use ExerSaucer in or near swimming pools or other bodies of water.
• DO NOT fill the ExerSaucer tray with water.
• DO NOT adjust height while baby is sitting in ExerSaucer.
• DO NOT use the ExerSaucer if it is damaged, broken, or is missing any parts.
• NEVER use as a sled.
• DO NOT allow child to sleep in ExerSaucer.
• DO NOT spin baby in seat. Only permit baby to rotate the seat.
• For use by children who are at least 4 months old AND can hold up their head and neck unassisted.
• FALL HAZARD! Stop using ExerSaucer when your child reaches any of the following developmental stages:
- Can walk;
- Is over 30” (76 cm) tall;
- Can stand flat-footed in the ExerSaucer in the highest adjustment level;
- Can climb out of the product.
• Allow only the baby’s toes to touch the base. DO NOT allow the baby to stand flat-footed on the base.
• DO NOT use or store this product outdoors.
• To avoid tip over, place product on flat, level floor.
• DO NOT mix old and new batteries.
• DO NOT mix alkaline and standard (carbon-zinc) batteries. Use only batteries of the same or equivalent type.
• DO NOT dispose of batteries in fire, as batteries may explode or leak.
• DO NOT use rechargeable batteries.
• DO NOT recharge non-rechargeable batteries.
• Promptly remove old batteries from the toy.
• Remove batteries before storing unit for a prolonged period of time.
Registration Information
Please register this product so we can reach you if there is a safety alert or recall. We will not sell, rent, or share your personal infor-
mation. To register your product, please complete and mail the card that came with it or visit our on-line registration at
http://plweb.evenflo.com/productreg.aspx
For future reference, record the Model Number and Date of Manufacture below.
Model Number: Date of Manufacture:
Phillips Screwdriver
CAUTION: Tighten all screws until snug; do not overtighten. Use only screws provided.
DO NOT USE POWER TOOLS.
Tools Required
To Next Page
Loading...
