Length
Total time over which Taps
are spaced. 4 sec max
TAP/Preset
Press & Hold to toggle between
Preset Select and Tap Modes
Taper
Left to fade up
Right to fade down
Center for equal level of all taps
Spread
Spacing of Taps
Turn left for ”slow-down”
Turn right for ”speed-up”
Center for constant spacing
TAP Button/LED
LED OFF = Preset Select Mode
LED ON = Tap Time in Seconds
LED Blinks = Tap Tempo in BPM
Press to toggle Tap Time/Tempo
Press & Hold to Save Preset
Button/LED
Toggles Primary/Secondary
Parameter Control
LED ON = Secondary
LED OFF = Primary
Taps
Number of Delay Taps
Mix
Dry/Wet Mix
Preset LED Ladder
Feedback
Repeats of a Length-valued
delay that is fed back around
the entire multi-tap machine
ACTIVE/BYPASS
Preset Mode: Load Preset
ACTIVE Button/LED
LED lit when ACTIVE
Press to toggle action of
ACTIVE Footswitch
LATCHING< >MOMENTARY
UltraTap Quick Reference Guide
Presets - 5 On Board, 127 Via MIDI
NOTE: Save Mode times out after a few seconds.
Pressing either Footswitch exits Save Mode.
Load Presets Save Presets
The currently loaded Preset is indicated on the Preset LED Ladder. When a Preset is modified the Preset LED
blinks once.
When a Preset is loaded or when toggling between Parameters using , Knob positions will not align with their
current Parameter values. As a result, turning a knob will likely cause an abrupt change in the sound.
With Catch Up ON, the sound does not change until the Knob is moved to the position corresponding to the
current value. The LED Ladder indicates whether the knob must be turned CCW (top LED blinks) or CW (bottom
LED blinks). The LED flashes more rapidly as the knob approaches the value set by the Preset. All five LEDs blink
once when the knob matches the stored Parameter value.
NOTE: To enable/disable Catch Up Knob Function, power up in System Setup mode and press TAP
Footswitch to toggle ON/OFF.
Catch Up Knob Function
To select and load a Preset using Footswitches:
1. TAP Footswitch selects Preset 1 to 5.
Preset 1 (top LED) to Preset 5 (bottom LED)
blinks.
2. ACTIVE Footswitch loads the Preset. LED stops
blinking.
To save one of the 5 Presets using the Buttons:
1. Press & hold TAP Button
- Blinking Ladder and Button LEDs let you know
you have entered Save Mode.
2. TAP Button selects Preset 1 to Preset 5.
3. ACTIVE Button saves Preset
- LEDs stop blinking to let you know the Preset
is saved.
NOTE: To select Preset, TAP Footswitch must be
in Preset mode. If TAP LED is lit, press and hold
TAP Footswitch.
UltraTap QRG for Firmware v1.0+| Eventide Part #141346 Rev A. Eventide is a registered trademark of Eventide Inc. © 2021 Eventide Inc.
Restore Factory Settings: Boot pressing ACTIVE Footswitch & ACTIVE Button
Software Update: Boot pressing TAP Button & TAP Footswitch
Device Manager Software
eventideaudio.com/edm
Instructional Videos
eventideaudio.com/UltraTap-pedal
Technical Support
eventideaudio.com/support
Follow us on Social
LED OFF Tap OFF
STATUS FUNCTION
Press TAP Footswitch to increment presets
TAP Footswitch Functionality
Press & Hold the TAP Footswitch to toggle between Tap mode and Preset Select mode.
Press the TAP Button/LED to toggle between Tap Time and Tap Tempo as follows:
LED ON
LED Blinks
at BPM
Tap Time
Tap Tempo
Tapping sets Length in seconds. Chop LFO Speed is continuous in Hz
Tapping sets tempo in BPM. Length, Predelay & Chop LFO Speed set
by Spd/Rise/Rel are all quantized to note durations.
EFFECT
Note: A single tap
will always reset
the LFO phase
UltraTap Signal Flow
To Next Page
Need help?
General
