To Next PageTo Next PageWhy is my Ex-Cell ZR3600 not producing enough pressure after using it normally?
Low pressure after normal use can stem from several issues. The seal or packing might be worn, or the valves could be worn or obstructed. Another possibility is a worn unloader piston or a worn E-Z start valve. For all these issues you should have the corresponding parts replaced by an Authorized Warranty Service Center (AWSC).
What to do if there is no or low pressure on initial use of my Ex-Cell ZR3600?
If your Ex-Cell Pressure Washer has no or low pressure upon initial use, consider these potential causes: * The chemical filter might be clogged: Clean it. * The chemical screen may not be submerged: Ensure the end of the chemical hose is fully submerged in the chemical. * The chemical might be too thick: Dilute the chemical to achieve a water-like consistency. * The pressure hose may be too long: Lengthen the water supply hose instead of the high-pressure hose. * There might be chemical build-up in the chemical injector: Have the parts cleaned or replaced by an Authorized Warranty Service Center (AWSC).
How to fix water leaking at the gun or spray wand connection on my Ex-Cell ZR3600 Pressure Washer?
If you notice water leaking where the gun connects to the spray wand of your Ex-Cell Pressure Washer, the issue might be a worn or broken o-ring; check and replace it if necessary. Also, ensure the hose connection is tight; if it's loose, tighten it.
What should I do if my Ex-Cell ZR3600 pump pulsates?
If your Ex-Cell Pressure Washer's pump pulsates, it could be due to worn oil seals, in which case you should have them replaced by an Authorized Warranty Service Center (AWSC). Another potential cause is a loose drain plug; ensure it is tightened.
What to do if my Ex-Cell ZR3600 Pressure Washer pump is leaking water?
If your Ex-Cell Pressure Washer pump is leaking water, check for loose connections and tighten them. If the connections aren't the issue, the piston packings might be worn, and you should have them replaced by an Authorized Warranty Service Center (AWSC).
What to do if my Ex-Cell Pressure Washer pump is leaking oil?
If your Ex-Cell Pressure Washer pump is leaking oil, the o-rings might be worn or broken and you should have them replaced by an Authorized Warranty Service Center (AWSC). Alternatively, the pump head or tubes might be damaged from freezing, which also requires replacement by an AWSC.
General| Maximum Pressure | 3600 PSI |
|---|---|
| Pump | Axial Cam |
| Engine Type | OHV |
| Engine | Honda GX390 |
| Hose Length | 25 ft |
| Nozzles Included | 0°, 25°, 40°, Soap |
Explains the meaning of DANGER, WARNING, and CAUTION symbols used in the manual.
Details hazards related to explosion or fire and how to prevent them.
Explains hazards from exhaust fumes and cleaning fluids.
Covers potential damage during transport or storage and prevention methods.
Details dangers of high-pressure fluid injection and how to avoid it.
Warns about chemical hazards and necessary precautions for safe handling.
Addresses general unsafe operation risks and how to prevent them.
Highlights dangers of electrical shock and necessary safety measures.
Warns about burns from hot engine components and surfaces.
Details dangers of high-velocity spray and projectile risks.
Explains the function of key components like the pump, engine, and hoses.
Details the controls and terminology related to the pressure washer's engine.
Describes operating features, including pressure adjustments and bypass mode.
Explains methods to lower pressure, including backing away and using different nozzles.
Guide on using the spray wand and changing different pressure nozzles.
Instructions for safely removing and installing spray nozzles on the wand.
Consult engine manual for manufacturer's specific maintenance recommendations.
Instructions for checking the engine oil level using the dipstick.
Step-by-step guide for draining and refilling the pump oil.
Provides a chart listing model numbers, pump types, oil types, and capacities.
Guide to cleaning a clogged spray wand nozzle and backflushing.
Instructions for cleaning the water inlet filter screen to ensure proper water flow.
Consult engine manual for manufacturer's recommendations for engine storage.
Details on draining the pump and hoses and using antifreeze for storage.
Troubleshooting steps for an engine that fails to start.
Diagnoses issues causing low or no pressure when first using the unit.
Troubleshooting for issues preventing the unit from drawing chemicals.
Addresses problems causing loss of pressure after the unit has been used.
Solutions for leaks occurring at the connection point of the gun and wand.
Troubleshooting for water leaks originating from the pump assembly.
Addresses issues causing oil leaks from the pump.
Diagnoses and resolves issues causing the pump to pulsate.
