Excel 11734 - Cross Cut 90° and Turntable 0°; Cross Cut 90° and Turntable 0° - 45°; Miter Cut 0°-45° and Turntable 0°; Miter Cut 0°-45° and Turntable 0°-45°

• Attachmentsweight: 1.5kg
CROSSCUT90° ANDTURNTABLE0°
Forcuttingwidthsuptoapprox.100mmitispossible
tofixthesaw‘sdragfunctionwiththelockingscrew
(22) fordragguideinrearposition.Ifthecuttingwidth
exceeds100mmyoumustensurethatthelocking
screw (22) fordragguideisslackenedandthatthe
machinehead (19) canbemoved.
·Movethemachinehead (19) toitsupperposition.
·
Usethehandle (1) topushbackthemachinehead
(19) andfixitinthispositionifrequired(dependent
onthecuttingwidth).
·
Placethepieceofwoodtobecutagainstthe
workpiecestop (15) andontheturntable (25).
·
Caution!Lockthematerialwiththeclampingdevice
(13) onthefixedsawtabletopreventthematerial
frommovingduringthecuttingoperation.
·
Clampflatmaterialinlyingpositionusingthevertical
clampingdevice.
·Alternatively,clampflatmaterialwhichyouwantto
cutinuprightpositionusingthehorizontalclamping
device.
· Toturnthesawon:pushtheswitchlock(24) toleft
meanwhiledepressandholdtheon/offtriggerswitch (2)
.
·Withthedragguidefixedinplace:Usethehandle (1)
tomovethemachinehead (19) steadilyandwithlight
pressuredownwardsuntilthesawblade (18) has
completelycutthroughtheworkpiece.
· Withthedragguidenotfixedinplace:Pullthe
machinehead (19) allthewaytothefrontandthen
usethehandle (1) tomoveitdownwardssteadilyand
withlightpressure.Nowpushthemachinehead (19)
slowlyandsteadilytotheverybackuntilthesaw
blade (18) hascompletelycutthroughtheworkpiece.
·Whenthecuttingoperationiscompleted,movethe
machinehead (19) backtoitsupper(home)position
andreleasetheOn/Offbutton (2) toturnthesawoff.
Important! The integral resetting springs will
automaticallyliftthemachinehead.Donotsimplylet
goofthehandle (1) aftercutting,butallowthe
machinehead (19) toriseslowly,applyingslight
counterpressureasitdoesso.
CROSSCUT90° ANDTURNTABLE0°-45°
Thecrosscutsawcanbeusedtomakecrosscutsof0°-
45° totheleftand0°-45° totherightinrelationto
thestoprail.
· Releasetheturntable (25) byundoingthelocking
screw (7) &Lockerlever (8).
· Turntheturntable (25) andscalepointertothe
desiredangularsettingonthedial (26) andlockinto
placewiththelockingscrew (7). Thesawhaslocking
positionsatanglesof-45°,-30°,-22.5°,-15°,0°,15°,
22.5°,30° and45°,atwhichtheturntable (25) audibly
clicksintoposition.
· Re-tightenthelockingscrew (7) tosecurethe
turntable (25) inplace.
·Cutasdescribedbefore.
MITERCUT0°-45° ANDTURNTABLE0°
Thecrosscutsawcanbeusedtomakemitercutsto
theleftof0°-45° andtotherightof0°-45° inrelation
totheworksurface.
·
Ifrequired,dismantletheclampingdevice (13) or
mountontheoppositesideofthefixedsawtable.
·Movethemachinehead (19) toitsupperposition.
·Fastentheturntable (25) in0°position.
·Cutasdescribedbefore.
MITERCUT0°-45° ANDTURNTABLE0°-45°
Thecrosscutsawcanbeusedtomakemitercutsto
theleftof0°-45° andtotherightof0°-45° inrelation
totheworksurface,withsimultaneoussettingofthe
turntablefrom0°-45° totheleftor0°-45° totheright
inrelationtothestoprail(doublemitercut).
·
Ifrequired,dismantletheclampingdevice (13) or
mountontheoppositesideofthefixedsawtable.
·Movethemachinehead (19) toitsupperposition
· Releasetheturntable (25) byundoingthelocking
screw (7) &Lockerlever (8).
·Usethehandle (1) toadjusttheturntable (25) tothe
anglerequired.
· Re-tightenthelockingscrew(7) tosecurethe
turntableinplace.
·Cutasdescribedbefore.
LIMITINGTHECUTTINGDEPTH
·
Thecuttingdepthcanbeinfinitelyadjustedusingthe