EXELAIR EX5005KIT - User Manual

Questions and Answers

G
Grant FarrellAug 5, 2025
How to fix EXELAIR Tools that has low air pressure?
- E
  Elizabeth BryantAug 5, 2025
  To fix low air pressure in your EXELAIR Tools, you should: a. Adjust the regulator on the tool to the maximum setting. b. Adjust the compressor regulator to the tool maximum of 90 PSI/6.3 BAR.
M
Mr. Marvin CallahanAug 10, 2025
Why is there moisture blowing out of my EXELAIR EX5005KIT exhaust?
- D
  Debra MurphyAug 10, 2025
  If you notice moisture blowing out of the exhaust of your EXELAIR Tools, it indicates water in the tank. You need to drain the tank. Then, oil the tool and run it until no water is evident. Finally, oil the tool again and run it for 1-2 seconds.
T
taylorbrendanAug 13, 2025
How to troubleshoot EXELAIR Tools with air hose leaks?
- S
  Samuel TorresAug 13, 2025
  To troubleshoot air hose leaks in your EXELAIR Tools, tighten and seal any leaking hose fittings. Use sealing tape to ensure a proper seal.
T
Thomas Edwards MDAug 18, 2025
What causes pressure drops in EXELAIR EX5005KIT?
- E
  Elizabeth LeAug 18, 2025
  Pressure drops in your EXELAIR Tools can be caused by: * Using an improperly sized hose. Long hoses or tools requiring large air volumes may need a hose with an I.D. of 1/2 inch or larger, depending on the total length of the hoses. * Using multiple hoses connected together with quick-connect fittings. This reduces the tool's power. Directly connect the hoses together instead.
M
melissaoconnellAug 22, 2025
How do I fix a worn rotor blade in EXELAIR Tools?
- M
  Mark Alvarez Jr.Aug 22, 2025
  If the rotor blade in your EXELAIR Tools is worn, you need to replace it.
M
matthew06Oct 26, 2025
Why does my EXELAIR Tools run slowly?
- C
  Chad HillOct 26, 2025
  Your EXELAIR Tools might be running slowly due to several reasons: * Grit or gum buildup: Flush the tool with air-tool oil or gum solvent. * Lack of lubrication: Lubricate the tool. * Low air pressure: Adjust the regulator on the tool to the maximum setting and the compressor regulator to a maximum of 90 PSI/6.3 BAR. * Air hose leaks: Tighten and seal any leaking hose fittings using sealing tape. * Pressure drops: Ensure the hose is the proper size (a 1/2 in. or larger I.D. may be needed for long hoses or tools using large air volumes) and directly connect hoses instead of using multiple quick-connect fittings. * Worn rotor blade: Replace the rotor blade. * Moisture in the exhaust: Drain the water from the tank and oil the tool, running it until no water is present. Then, oi...
J
John VillarrealOct 31, 2025
What to do if EXELAIR EX5005KIT Tools won't operate?
- K
  kevin91Oct 31, 2025
  If your EXELAIR Tools won't operate, consider these potential causes and solutions: 1. Check for grit or gum: Flush the tool with air-tool oil or gum solvent. 2. Ensure lubrication: Lubricate the tool properly. 3. Verify air pressure: Adjust the tool regulator to its maximum setting and the compressor regulator to a maximum of 90 PSI/6.3 BAR. 4. Inspect air hose: Tighten and seal any hose fittings that are leaking, using sealing tape if necessary. 5. Address pressure drops: Use the correct hose size (potentially a 1/2 in. I.D. or larger for long hoses or high-volume tools) and avoid connecting multiple hoses with quick-connect fittings; connect them directly. 6. Check rotor blade: Replace the rotor blade if it's worn. 7. Remove moisture: Drain the water from the tank. Oil the tool ...