EYELA LTI-1200E User Manual (English)

Questions and Answers:

D
Debra PattersonAug 21, 2025
Why is my EYELA Accessories unit not cooling down properly?
- R
  Raymond GarzaAug 21, 2025
  If your EYELA Accessories unit isn't cooling down well, check the setting temperature to ensure it's appropriate. If the ambient temperature is too high, set the value at 30°C (LTI-400E) or lower than 35°C. Also, too many samples and vessels in the chamber can prevent convection flow of heat, so reduce their number. If the refrigeration unit is frosted, check the condition of frost formation and execute manual forced Defrosting. In case the refrigeration unit does not work, immediately stop running the product and contact your local agency or the closest customer service center.
B
Brian HillAug 22, 2025
What should I do if the EYELA LTI-1200E refrigeration unit does not work properly?
- M
  murphyrobertAug 22, 2025
  If the refrigeration unit of your EYELA Accessories does not work properly, reduce the load. For the settings for under cooling protector, set the temperature -10° lower than setting temperature of temperature controller. In case the setting temperature is too high, set the value up to 40°.
C
Chad HoffmanAug 25, 2025
What to do if no display is shown on the indicator of EYELA Accessories when turning on power switch?
- N
  Nathan PenningtonAug 25, 2025
  If there's no display when you turn on the power switch of your EYELA Accessories, first, turn off the residual current device and power switch, then ensure the power plug is securely connected to the outlet. Also, check if the breaker of distribution board is on. Ensure the residual current device is turned on. If the residual current device is impaired, immediately stop running the product and contact your local agency or the closest customer service center.
K
Kristen MorganAug 26, 2025
What should I do if the temperature of my EYELA Accessories does not rise up to the setting value?
- T
  thompsonchristopherAug 27, 2025
  If the temperature of your EYELA Accessories unit does not rise to the set value, reduce the number of sample and vessel. For the settings for under cooling protector, set the temperature 10° higher than setting temperature of temperature controller. In case the setting temperature is too low, set the value higher than 30°. If the ambient temperature is too low, set the temperature higher than 5°.
J
Jasmine ParkerAug 27, 2025
Why can't my EYELA Accessories unit be temperature controlled?
- G
  Glenn McphersonAug 27, 2025
  If your EYELA Accessories unit cannot be temperature controlled, it may be because the heater is disconnected or the refrigeration unit is impaired. If the heater is disconnected, immediately stop running the product and contact your local agency or the closest customer service center.
B
Brian LawrenceAug 29, 2025
What causes the upper temperature limit alarm to activate on my EYELA LTI-1200E?
- D
  David SimmonsAug 29, 2025
  The upper temperature limit alarm on your EYELA Accessories can activate if too many samples and vessels in the chamber prevents the convection flow of the heat. Reduce the number of sample or vessel to resolve this.
M
Michelle MaysAug 31, 2025
Why does the EYELA LTI-1200E Accessories refrigeration unit not start up smoothly?
- E
  Elizabeth FarmerAug 31, 2025
  The refrigeration unit might not start smoothly because the protection timer is working. To protect the unit from overload start-up, the timer starts automatically after the refrigeration unit stops. The timing is as follows: LTI-400E: 210 sec, LTI-700E: 80 sec, LTI-1200E: 80 sec.
J
jacob94Sep 1, 2025
What does it mean if the power failure alarm is activated on my EYELA LTI-1200E Accessories?
- A
  Adam SmithSep 1, 2025
  The power failure alarm activates on your EYELA Accessories if a power failure occurred during unit control or if the power switch was turned off without stopping control first. To resolve this, always stop controlling before turning the power switch off. Press the [Set] key to cancel the alarm.
B
Brian HaneySep 3, 2025
What to do if the sensor alarm is activated on my EYELA LTI-1200E Accessories?
- A
  adamrobertsSep 3, 2025
  If the sensor alarm is activated on your EYELA Accessories, it indicates that the temperature sensor is disconnected. Immediately stop running the product and contact your local agency or the closest customer service center.
B
Brooke JonesSep 5, 2025
Why is there dew condensation on the wall of the EYELA LTI-1200E chamber?
- H
  Hannah FlynnSep 5, 2025
  Dew condensation on the wall of the EYELA Accessories chamber can occur depending on the settings, ambient temperature, or humidity in the chamber. Wipe the dew off with a soft cloth.