To Next PageTo Next PageWhat causes the over heat alarm to activate on my EYELA LTI- 400E Accessories?
The over heat alarm activates on your EYELA Accessories if the setting value for the over heat protector is too low. For the settings for over heat protector, set the temperature +10° higher than the setting temperature of the temperature controller. If the setting temperature is too high, set the value up to 30°.
What causes the lower temperature limit alarm to activate on my EYELA Accessories?
The lower temperature limit alarm on your EYELA Accessories can activate if too many samples and vessels in the chamber prevents the convection flow of the heat, or if the heater is disconnected. Reduce the number of sample or vessel. If the heater is disconnected, immediately stop running the product and contact your local agency or the closest customer service center.
Why is the temperature not stable in my EYELA Accessories?
Temperature instability in your EYELA Accessories can be caused by constant changes in room temperature due to the influence of an air conditioner. Ensure the unit is placed where the air conditioner's airflow does not directly affect it.
What should I do if the door alarm, temperature control failure alarm, or temperature not rising alarm is activated on my EYELA LTI- 400E?
If the door alarm, temperature control failure alarm, or temperature not rising alarm is activated on your EYELA Accessories, it's likely that the door is not closed completely. Ensure the door is fully closed.
What to do if the over load alarm for refrigeration unit is activated on my EYELA LTI- 400E?
If the overload alarm for the refrigeration unit is activated on your EYELA Accessories, it indicates that the heat load is too heavy. Reduce the load.
General| Brand | EYELA |
|---|---|
| Model | LTI- 400E |
| Category | Accessories |
| Language | English |
Explains warning signals and their meanings.
Describes the product's intended use.
Accessory for shaker, incubator, or stirrer.
Counter with caster for additional equipment.
Clamp for stacking two LTI-400E units.
10W lamp for chamber illumination.
Unit for day-and-night operation.
Outputs measured temperature data for recording.
Outputs abnormal conditions via contact points.
Details the components and functions of the control panel.
Continuous operation at a set temp. Can be started/stopped with Run/Stop key.
Allows timed operations: auto stop, auto start, 1-step.
Calibrates displayed temp. to match a standard gauge.
Sets the upper limit for temperature alarms.
Sets the lower limit for temperature alarms.
Selects unit behavior after power interruption.
Configures buzzer behavior for auto stop completion.
Sets time for total operation hours display.
Resets total operation hours for maintenance timing.
Activates if chamber temp. exceeds set threshold.
Activates if chamber temp. drops below set threshold.
Activates if the door is not properly closed.
Triggers if temp. control deviates significantly.
Activates upon power interruption or improper shutdown.
Activates if the temp. sensor is disconnected.
Activates if the refrigeration unit experiences overload.
Resets microcomputer if abnormal conditions arise.
Activates when heater temp. exceeds limits.
Activates when refrigeration unit temp. drops too low.
Warns when total operation hours exceed the set time.
Specifies suitable environmental conditions for installation.
Details necessary clearances and handling precautions.
Specific precautions for moving and leveling the LTI-1200E.
Instructions on how to secure the unit to the floor.
Instructions for installing a shelf for shaker use.
Covers initial setup steps before operation.
Instructions for setting the drain port plug.
How to remove and use outlet caps.
Instructions for installing shelf boards.
Instructions for using the cable port.
Instructions for setting the hatch clip with key.
Steps for connecting the power plug to the outlet.
Configures the over heat and over cool protection settings.
Selects refrigeration mode and controls blower operation.
Details for setting, starting, and stopping constant number operation.
Guides for setting, running, and stopping various timer modes.
Instructions for starting and stopping the Auto Stop timer mode.
Instructions for starting and stopping the Auto Start timer mode.
Guides for setting, starting, and stopping the 24-hour cycle operation.
Calibrates displayed temp. to match a standard gauge.
Adjusts the setting for the upper temperature limit alarm.
Adjusts the setting for the lower temperature limit alarm.
Configures unit's behavior after power recovery.
Configures buzzer behavior for auto stop completion.
Configures the display for total operation hours.
Resets total operation hours for maintenance timing.
Initiates manual defrosting by pressing the Def key.
Describes temp. changes during manual defrosting.
Allows manual interruption of defrosting.
Procedure for testing the residual current device.
Guidelines for cleaning and maintaining the unit.
Details the components and structure of the door.
