Fabtech FTS8023 User Manual

4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710
FTS8023 / FTS8046
Dual Steering Stabilizer System
2005-15 Ford F250 & F350 4WD
Qty
Part #
Description FTS8023
2 FT7006 Steering
Stabilizer
1 FT30145BK Axle
Bracket
2 FT30149 Tie Rod Brackets
1 FT739U Axle U-Bolt
1 FT30312 Hdwr Sub-Assembly Kit
FT30312 Hdw
r Sub-Assembly Kit
Qty
Part # Description
4 FT740U Tie Rod U-Bolt
2 FT140357 Shock Stud Kit
1 FT58H Axle u-bolt hardware
8 37160003052 3/8"-16 Nyloc Nut
8 37000005081 3/8" SAE Flat Washer
2 50132001081 1/2"-13 x 2" Hex Bolt
2 50000005081 1/2" SAE Flat Washer
1 FTLOCK Thread Locking Compound
1 FTAS12 Sticker
1 FTREGCARD Registration Card
2 FT8023i Instruction
Sheet
TOOL LIST:
 Assorted Metric & Standard Wrenches
 Torque Wrench
 Measuring Tape

Die Grinder With Cut-Off Wheel
READ BEFORE BEGINNING INSTALL
READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION.
DO NOT ALTER THE FINISH OF THESE COMPONENTS, EX
AMPLE- CHROMING, ZINC PLATING OR
PAINTING. CHANGING THE FINISH CAN CAUSE STRUCTURAL FATIGUE OF COMPONENTS.
THIS STABILIZER KIT WILL NOT WORK ON STOCK HEIGHT VEHICLES. IT IS DESIGNED TO WORK ONLY
ON VEHICLES WITH FABTECH LIFT SYSTEMS
THIS SYSTEM WILL ONLY WORK IN CONJUCTION WITH FABTECH 4”, 6”, 8” AND 10” LIFT SYSTEMS.
Qty
Part #
Description FTS8046
2 FTS6604
Steering
Stabilizer
1 FT30145BK Axle
Bracket
2
FT30149 Tie Rod Brackets
1
FT739U Axle U-Bolt
1
FT30312 Hdwr Sub-Assembly Kit
FT30312 Hdw
r Sub-Assembly Kit
Qty
Part # Description
4
FT740U Tie Rod U-Bolt
2
FT140357 Shock Stud Kit
1
FT58H Axle u-bolt hardware
8 37160003052 3/8"-16 Nyloc Nut
8 37000005081 3/8" SAE Flat Washer
2 50132001081 1/2"-13 x 2" Hex Bolt
2 50000005081 1/2" SAE Flat Washer
1
FTLOCK Thread Locking Compound
1 FTAS12 Sticker
1 FTREGCARD Registration
Card
2 FT8023i Instruction
Sheet

Fabtech FTS8023 Specifications

General

Brand	Fabtech
Model	FTS8023
Category	Automobile Accessories
Language	English

Summary

Preparation and Warnings

Tool List

List of required tools for installation, including wrenches, torque wrench, measuring tape, and die grinder.

Read Before Beginning Installation

Instructions to read all steps thoroughly and warnings against altering component finishes.

Begin Installation Steps

Disconnect Battery and Prepare Axle Brackets

Disconnect battery, position truck, and attach axle brackets with shock stud kits to front axle holes.

Attach Tie Rod Brackets and Stabilizers

Position tie rod end brackets and attach steering stabilizers to axle and tie rod brackets.

Torque Axle and Tie Rod Brackets

Torque axle bracket U-bolts to 80 ft lbs and tie rod bracket U-bolts to 32 ft lbs.

Final Installation Checks

Trim U-Bolt Flesh and Check Clearance

Trim residual U-bolt length after torquing and steer the truck to check for stabilizer bottoming out.

Re-torque Hardware

Re-torque all hardware after 200 miles to ensure continued proper function and safety.