COMBI 740 TECHNICAL SPECIFICATIONS
ELECTRIC MOTOR, TWO PHASE CLASS H
Power output.........................................................................................0.18KW (0.25HP)
Absorbed power.......................................................................................................250W
Frequency...................................................................................................................50Hz
Supply voltage.................................................................................................230V ±10%
Absorbed current.......................................................................................................1.2A
Capacitor..................................................................................................................12.5μF
Motor rotation speed ....................................................................................1˙350 r.p.m.
Intermittent service.......................................................................................................S3
PERFORMANCE (for 110°)
Duty service cycles.............................18s Open - 30s Dwell - 18s Close - 30s Dwell
Time of one complete cycle......................................................................................96 s
No. Completed cycles Open - Dwell - Close - Dwell ......................................37/hour
No. cycles a year, 8 hours of operation a day .................................................108˙000
DOUBLE STROKE JACK AND OIL-HYDRAULIC PUMP
Pump flow rate - P3.............................................................................................0.85
/1’
Working pressure .....................................................................................1 MPa (10bar)
Max pressure ............................................................................................3 MPa (30bar)
Working temperature.................................................................................-20°C +80°C
Rotation time (110°).....................................................................................................18 s
Rotation time (175°).....................................................................................................28 s
Oil type.................................................................................................................Oil Fadini
Shaft rotation angle ........................................................................................110° / 175°
Torque.............................................................................................................250-400 Nm
Cylinder bore...........................................................................................................75 mm
Stroke .......................................................................................................................52 mm
Weight of Combi 740 with accessories ................................................................27 Kg
IP standards...............................................................................................................IP 67
Leaf maximum static weight ....................700 Kg(1.0m length) - 350Kg(2.8m length)
Overall dimensions (LxWxH)...............................................................475x305x130 mm
COMBI 740 OVERALL DIMENSIONS
5
0
190
40
10
PLATE WITH SQUARE HOLE FERRULE
(FOR HYDRAULIC JACKS
WITHOUT A HYDRAULIC LOCK)
295
465
10
300
130
470
270
340
145
270
395
145
EMERGENCY MANUAL RELEASE WITH
SQUARE FERRULE, RELEASE KEY
WELDING PLATE
(FOR HYDRAULIC JACKS WITH A HYDRAULIC LOCK)
ENCLOSURE COVER
MADE OF ALUMINIUM OR
STAINLESS STEEL (OPTIONAL)
COMBI 740 110°
CABLE 4x1 mm
2
=2.50 METERS
COMBI 740 175°
CABLE 4x1 mm
2
=2.50 METERS
HOUSING ENCLOSURE
(ZINC-COATED OR STAINLESS STEEL)
PIC. 26
The MECCANICA FADINI'S development has always been based on ensuring the quality of products and on the
existence of a TOTAL QUALITY CONTROL system, which guarantees quality levels over time as well as constant
updating in compliance with European standards, in order to ensure continued improvement.
ORDINARY MAINTENANCE
To ensure optimal system performance over time and according to safety regulations, it is necessary to carry out correct maintenance and monitoring
of the entire installation: the automation, the electronic equipment installed and all cabling attached to such equipment. Installation must be
completed by qualified technical personnel, filling out the Maintenance Manual indicated in the Regulations Booklet to be requested:
- Oil-hydraulic automation: maintenance check at least every six months.
- Electronic equipment and safety systems: maintenance check at least once per month.
- Scheduled and extraordinary maintenance operations must be agreed upon between the client and the company that will perform the work.
- Leave the handling of all packaging materials including cardboard, nylon, polystyrene, etc... to companies that specialise in waste recovery.
- THROWING AWAY MATERIALS HARMFUL TO THE ENVIRONMENT IS PROHIBITED
- In case the actuator is removed, do not cut the electrical wires; instead remove them from the terminal board by loosening the screws inside
the junction box.
The manufacturer reserves the right to make amendments to this manual without prior
notice and declines all responsibility for any errors, personal injury or damage to property.
Via Mantova, 177/A - C.P. 126 - 37053 Cerea (Verona) Italy
Tel. +39 0442 330422 r.a. - Fax +39 0442 331054
e-mail: info@fadini.net - www.fadini.net
s.n.c.
AUTOMATIC GATE MANUFACTURERS
DISPOSE OF PROPERLY
ENVIRONMENT-NOXIOUS MATERIALS
2003/108/CE Directive
for waste electrical and
electronic equipments
GB
32
English
Ø12
175
46
73
75
210
17
36
DOUBLE STROKE JACK AND OIL-HYDRAULIC PUMP
/1’
Working temperature.................................................................................-20°C +80°C
Rotation time (110°).....................................................................................................18 s
Rotation time (175°).....................................................................................................28 s
Oil type.................................................................................................................Oil Fadini
Shaft rotation angle ........................................................................................110° / 175°
Torque .............................................................................................................250-400 Nm
Cylinder bore...........................................................................................................75 mm
Stroke .......................................................................................................................52 mm
Weight of Combi 740 with accessories ................................................................27 Kg
IP standards ...............................................................................................................IP 67
Leaf maximum static weight....................700 Kg(1.0m length) - 350Kg(2.8m length)
Overall dimensions (LxWxH)...............................................................475x300x140 mm
Pump ow rate - P3..............................................................................................0.85
To Previous Page
Loading...
