Section Page
3.2.2. Locking/Unlocking of memory ......................................................................................22
3.2.3. Deletion of a complete program......................................................................................22
3.2.4. Change of program number.............................................................................................22
3.2.5. Display and search of memorized subroutines ...............................................................22
3.2.6. Selection of a program ....................................................................................................22
3.2.7. Creating a program ..........................................................................................................23
3.2.8. Deletion of a block ..........................................................................................................23
3.2.9. Copy a program ...............................................................................................................23
3.3. MODE 3: TEACH-IN.......................................................................................................24
3.3.1. Selection of the operating mode TEACH-IN..................................................................24
3.3.2. Locking/Unlocking of memory.......................................................................................24
3.3.3. Deletion of a complete program......................................................................................24
3.3.4. Change of program number ............................................................................................24
3.3.5. Display and search of memorized subroutines ...............................................................24
3.3.6. Selection of a program ....................................................................................................24
3.3.7. Program creation .............................................................................................................25
3.3.8. Deletion of a block ..........................................................................................................25
3.3.9. Copy a program ...............................................................................................................25
3.4. Mode 4: DRY RUN.........................................................................................................26
3.4.1. Execution of a program ...................................................................................................26
3.4.1.1. Selection of the operating mode DRY RUN (4) .............................................................26
3.4.1.1.1. Selection of execution mode ...........................................................................................28
3.4.1.2. Selection of the program to be executed .........................................................................29
3.4.1.3. Selection of starting block...............................................................................................29
3.4.1.4. Display of the contents of the blocks ..............................................................................29
3.4.1.5. Cycle Start .......................................................................................................................29
3.4.1.6. Cycle Stop .......................................................................................................................29
3.4.1.7. Change of operating mode ..............................................................................................29
3.4.1.8. Tool inspection ................................................................................................................30
3.4.2. Display modes .................................................................................................................30
3.5. Mode 5: JOG ...................................................................................................................31
3.5.1. Selection of the JOG operating mode .............................................................................31
3.5.2. Search for machine reference axis by axis......................................................................32
3.5.3. Presetting a coordinate value ..........................................................................................32
3.5.4. Jogging the axes ..............................................................................................................33
3.5.4.1. Continuous movement.....................................................................................................33
3.5.4.2. Incremental movement ....................................................................................................34
3.5.5. Entering F,S and M .........................................................................................................34
3.5.5.1. Entering an F value .........................................................................................................34
3.5.5.2. Entering an S value .........................................................................................................35
3.5.5.3. Entering an M value ........................................................................................................35
3.5.6. Operation of the CNC as a readout .................................................................................35
3.5.7. Change of measurement units .........................................................................................36
3.5.8. Handwheel operation.......................................................................................................36
3.5.9. Display/Modification of RANDOM table.......................................................................37
3.5.10. Measuring and loading of tool offsets with a probe .......................................................40
3.5.11. Spindle operating keys ....................................................................................................41
3.6. Mode 6: EDITING ..........................................................................................................42
3.6.1. Selection of the operating mode EDITING(6)................................................................42
3.6.2. Locking/Unlocking of memory and formatting of 512 Kb memory ..............................42
3.6.3. Part-program directory ....................................................................................................43
3.6.3.1. Deletion of a complete program......................................................................................43
3.6.4. Change of program number ............................................................................................44
3.6.5. Display and search of subroutines stored in memory .....................................................44
3.6.6. Selection of a program ....................................................................................................45
3.6.7. Creating a program..........................................................................................................45
3.6.7.1 Displaying the block contents .........................................................................................45
3.6.7.2. Unassisted programming.................................................................................................46
3.6.7.3. Modification and deletion of a block ..............................................................................47
3.6.7.4. Assisted programming.....................................................................................................48
To Next Page
Loading...
