What to do if my Falco VL30F230B lift does not work?
If your Falco Lifting Systems lift isn't working, there could be several reasons. First, ensure the main switch is turned on. If it is, check for a power outage and restore power if necessary. Also, inspect the electrical wires for disconnections and replace them if needed. Finally, check the fuses and replace them if they are blown.
Why Falco VL30F230B lift does not lower when pressing the LOWERING-button?
If your Falco Lifting Systems lift doesn't lower when you press the lowering button, it could be due to a few reasons. The motor may not be operating properly, failing to release the mechanical safeties, so you should check the motor. Alternatively, the circuit board could be faulty and need replacement. Lastly, the lowering button itself might be faulty; check its operation and connections, and replace it if necessary.
What to do if my Falco Lifting Systems lift isn’t raising synchronous?
If your Falco Lifting Systems lift isn’t raising synchronously, it might be due to air or dripping in the hydraulic circuit. In this case, you should bleed the hydraulic circuit. Another possible cause is damaged cylinder gaskets, which should be checked and replaced if necessary.
What to do if Falco VL30F230B lift does not stop at the safety height during lowering?
If your Falco Lifting Systems lift doesn't stop at the safety height when lowering, the safety height limit switch may not be adjusted correctly or could be faulty, so adjust or change the limit switch. The circuit board might also be faulty, requiring replacement. Another possibility is a faulty lowering button, which should be checked and replaced if necessary. Finally, the lowering solenoid valve may not be discharging; verify if it is powered and check the magneto for damages, replacing it if disconnected or burnt.
Why Falco Lifting Systems lift does not raise when the LIFT-button is pressed?
If your Falco Lifting Systems lift doesn't raise when you press the lift button, it could be because the motor direction of rotation is incorrect, so interchange the phases on the main switch. Another reason might be insufficient oil in the hydraulic unit, so add some hydraulic oil. Also, the lifting button itself could be faulty; check its operation and replace it if needed. Finally, the suction pump filter may be dirty, requiring a check and cleaning.
What to do if Falco VL30F230B lift does not lift or lower smoothly?
If your Falco Lifting Systems lift does not lift or lower smoothly, it could be due to leakages or air in the hydraulic circuit; bleed the hydraulic system. Alternatively, the pump filter may be dirty, so check and clean it. Also, the pump suction could be blown, so check the seal and replace it if needed.
Why Falco Lifting Systems lifting capacity is not sufficient?
If the lifting capacity of your Falco Lifting Systems lift is not sufficient, it could be due to insufficient oil in the tank, so fill the oil in the tank. The pump might also be faulty, so check the pump and replace it if necessary. Another potential cause is an incorrectly adjusted maximum pressure valve, so adjust it correctly.
What happens if the motor does not stop when reaching maximum height in Falco Lifting Systems?
If the motor in your Falco Lifting Systems lift doesn't stop when reaching maximum height, the maximum height limit switch may not be working. Check the limit switch and replace it if needed.
Guidelines for proper storage and use of the user manual for the lift.
Essential safety regulations for operating the lift, covering personal gear and work area.
Description of built-in safety features preventing overload and unintended lowering.
Criteria for selecting a suitable installation location, including lighting and floor specifications.
Instructions for safe handling, transport, storage, and unpacking of lift components.
Recommendations for storing packages safely, considering temperature and humidity.
Procedures for opening packages, checking for damages, and ensuring all parts are present.
Step-by-step instructions for physically assembling the lift and its control unit.
Procedure for initial testing of lift functions and bleeding the hydraulic system without a load.
Steps for conducting operational tests of the lift with a vehicle loaded onto it.
Overview of the main power switch and operational buttons on the control panel.
Detailed steps for safely lifting a vehicle to the desired height.
Instructions for safely lowering the lift and the vehicle.
Procedure for preparing the lift for movement and safely relocating it.
Routine monthly tasks including cleaning and lubrication of pivot points.
Scheduled maintenance activities to be performed every three months.
Detailed checklist for periodic mechanical and hydraulic checks and maintenance.
General| Brand | Falco |
|---|---|
| Model | VL30F230B |
| Category | Lifting Systems |
| Language | English |
To Next Page
