FALMEC ZENITH NRS - Safety Instructions and Warnings; Technical Safety; Intended Use

18
SAFETY INSTRUCTIONS
AND WARNINGS
Installation operations are to be carried out
by skilled and qualied installers in accord-
ance with the instructions in this booklet and in
compliance with the regulations in force.
DO NOT use the hood if the power supply cable
or other components are damaged: disconnect the
hood from the electrical power supply and contact the
Dealer or an authorised Servicing Dealer for repairs.
Do not modify the electrical, mechanical or func-
tional structure of the equipment.
Do not personally try to carry out repairs or re-
placements. Interventions carried out by incom-
petent and unauthorised persons can cause seri-
ous damage to the unit or physical and personal
harm, not covered by the Manufacturer's warranty.
WARNINGS FOR THE INSTALLER
TECHNICAL SAFETY
Before installing the hood, check the integ-
rity and function of each part. Should
anomalies be noted, do not proceed with installa-
tion and contact the Dealer.
Do NOT install the hood if an aesthetic (or cos-
metic) defect has been detected. Put it back into
its original package and contact the dealer.
No claim can be made for aesthetic (or cosmetic)
defects once it has been installed.
During installation, always use personal protective
equipment (e.g.: Safety shoes) and adopt prudent
and proper conduct. The installation kit (screws and
plugs) supplied with the hood is only to be used on
masonry walls: in case of installation on walls of a dif-
ferent material, assess other installation options keep-
ing in mind the type of wall surface and the weight
of the hood (indicated on page 2). Keep in mind that
installations with dierent types of fastening systems
from those supplied, or which are not compliant, can
cause electrical and mechanical seal danger. Do not
install the hood outdoors and do not expose it to at-
mospheric elements (rain, wind, etc.).
ELECTRICAL SAFETY
The electrical system to which the hood is
to be connected must be in accordance
with local standards and supplied with earthed
connection in compliance with safety regulations
in the country of use. It must also comply with
European standards regarding radio antistatic
properties.
Before installing the hood, check that the electrical
mains power supply corresponds with what is report-
ed on the identication plate located inside the hood.
The socket used to connect the installed equipment to
the electrical power supply must be within reach: other-
wise, install a mains switch to disconnect the hood when
required. Any changes to the electrical system must be
carried out by a qualied electrician. The maximum
length of the ue fastening screws (supplied by the man-
ufacturer) must be 13 mm. Use of non-compliant screws
with these instructions can lead to danger of an electri-
cal nature. Do not try to solve the problem yourself in the
event of equipment malfunction, but contact the Dealer
or an authorised Servicing Department for repairs.
When installing the hood, disconnect the
equipment by removing the plug or switch-
ing o the main switch.
FUMES DISCHARGE SAFETY
Do no connect the equipment to discharge
pipes of fumes produced from combustion
(for example boilers, replaces, etc.).
Before installing the hood, ensure that all standards in
force regarding discharge of air out of the room have
been complied with.
USER WARNINGS
These warnings have been drawn up for your
personal safety and those of others. You are
therefore kindly asked to read the booklet carefully
in its entirety before using the or cleaning the equip-
ment. The Manufacturer declines all responsibility
for any damage caused directly, or indirectly, to per-
sons, things and pets as a consequence of failing to
comply with the safety warnings indicated in this
booklet. It is imperative that this instructions book-
let is kept together with the equipment for any fu-
ture consultation.
If the equipment is sold or transferred to another per-
son, make sure that the booklet is also supplied so that
the new user can be made aware of the hood's opera-
tion and relative warnings. After the stainless steel hood
has been installed, it will need to be cleaned to remove
any residues remaining from the protection adhesive as
well as any grease and oil stains which, if not removed,
can cause irreversible damage to the hood surface. To
properly clean the unit, the manufacturer recommends
using the supplied moist wipes, which are also available
sold separately.
Insist on original spare parts.
INTENDED USE
The equipment is solely intended to be used to
extract fumes generated from cooking food in
non-professional domestic kitchens: any other use
is improper. Improper use can cause damage to per-
sons, things, pets and exempts the Manufacturer
from any liability.