EasyManua.ls Logo

FeelTech FY-6800 - User Manual

FeelTech FY-6800
50 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
FeelTech
FY6600 Series Fully Numerical Control
Dual Channel Function/Arbitrary Waveform Generator
User’s Manual
Rev2.2 July,2017

Table of Contents

Questions and Answers

  • C
    Chris GrimesAug 6, 2025
    What to do if my FeelTech Portable Generator is set correctly, but there's no waveform output?
    • L
      lindagarciaAug 6, 2025
      If your FeelTech Portable Generator is set correctly but there is no waveform output, try these steps: 1. Ensure the BNC cable is securely connected to the CH1 or CH2 connector. 2. Inspect the BNC cable for any internal damage. 3. Verify the BNC cable is tightly connected to the test instrument. 4. Confirm that the indicators for CH1 or CH2 are turned on; if not, press the corresponding button to activate them.
  • W
    William OrtegaAug 16, 2025
    How to fix a dark screen on my FeelTech FY-6800 Portable Generator after switching it on?
    • D
      David GeorgeAug 16, 2025
      If the screen of your FeelTech Portable Generator remains dark after switching it on, try the following: 1. Ensure the power is correctly connected. 2. Verify that the power switch is fully engaged. 3. Restart the instrument after checking the connections.
  • N
    nvasquezAug 26, 2025
    Why is CH2 locked on my FeelTech Portable Generator, and how can I unlock it?
    • K
      Krista GilmoreAug 26, 2025
      If CH2 is locked on your FeelTech Portable Generator, here are some steps to try: 1. Check that the signal generator is operating in synchronous state. Press the SYNC button to enter the synchronization settings interface to cancel all synchronization parameters. 2. If the problem persists, restart the generator.

Summary

Guaranty and Declaration

Copyright and Trademark

Legal notices regarding intellectual property and brand registration.

Declaration and Contact Information

Statements on modification rights, liability, and customer support details.

Product Introduction

Quick Start Guide

General Inspection Procedures

Steps for inspecting the shipping container, instrument, and accessories upon receipt.

Front Panel Overview

Back Panel Overview

Power On and Initial Setup

Connect to Power

Instructions for connecting the instrument to AC power.

Power On and Self-Inspection

Procedure for turning on the instrument and initial self-inspection.

System Language Selection

How to select between English and Chinese system languages.

User Interface Navigation

Dual Channels Parameters Display

Description of the default display mode showing parameters for both channels.

Appearance and Dimensions

Front Panel Operations

Waveform Output Configuration

How to output waveforms from the channels, including default settings.

Selecting Output Channels

Instructions on how to select CH1 or CH2 for output configuration.

Waveform Selection

Guide to choosing different waveform types available on the generator.

Setting Output Frequency

Setting Output Amplitude

Setting DC Offset

Duty Cycle and Pulse Width Settings

Setting Output Phase

Enabling and Disabling Output

Example: Output Sine Waveform

Burst Waveform Generation

Enabling Burst Function

How to activate and configure the burst function, including trigger modes and cycle count.

Numerical Modulation

Frequency Meter and Counter

Enabling the Counter Function

Steps to enable the counter and measurement menu, and input signal sources.

Counter Configuration

Gate Time Settings

How to select gate time for counter measurements.

Input Coupling Modes

Setting the AC or DC coupling mode for signal input.

Sweep Function Overview

Sweep Object Selection

Explanation of selectable sweep objects like frequency, amplitude, offset, and duty cycle.

Setting Sweep Start Position

Setting Sweep End Position

Sweep Time and VCO Sweep

Sweep Type Selection

Enabling and Controlling Sweep

Start and End Value Definition

Defining the start and end parameters for sweep operations.

System Configuration and Auxiliary Functions

System Configuration Settings

Configure language, buzzer, uplink mode, and default output status.

Save and Load Parameters

Detailed Configuration Options

Uplink Operation Setup

Synchronization Function Setup

Troubleshooting Guide

Technical Specifications

Frequency and Waveform Specifications

Details on frequency ranges and various waveform characteristics.

Output and Measurement Specifications

Specs for amplitude, offset, phase, TTL/CMOS output, and external measurement.

Sweep, Modulation, and Burst Specifications

Details on sweep types, VCO, digital modulation, and burst function.

General Device Specifications

Overall specs including display, power, interface, dimensions, and weight.

Appendix

Safety Notes

Important safety precautions for using the instrument.

Warning and Personal Injury

Warnings regarding product misuse and potential personal injury.

Accessories and Options

List of standard accessories and optional equipment for the FY6600.

Warranty Information

Information regarding the product warranty, coverage, and exclusions.

FeelTech FY-6800 Specifications

General IconGeneral
BrandFeelTech
ModelFY-6800
CategoryPortable Generator
LanguageEnglish

Related product manuals