Fer FERtech F 32 D - User Manual

Questions and Answers

C
Chad HarmonSep 8, 2025
What does it mean if my Fer FERtech F 32 D has a Heating sensor fault?
- C
  cbrownSep 9, 2025
  If your Fer Boiler is showing a heating sensor fault, the sensor may be damaged. Replace the sensor.
V
Veronica ColonAug 23, 2025
Why is my Fer FERtech F 32 D showing a gas valve fault?
- J
  Jose KingAug 23, 2025
  A gas valve fault in your Fer Boiler can arise from modulating operator wiring disconnected, requiring a check of the wiring. Alternatively, it might be due to a faulty gas valve, necessitating a check and potential replacement of the valve.
A
Andrew OdonnellAug 25, 2025
What to do if my Fer Boiler activates overtemperature protection?
- R
  Roger KennedyAug 26, 2025
  If your Fer Boiler activates overtemperature protection, it may be due to a damaged heating sensor. Check the correct positioning and operation of the heating sensor. It could also be caused by no water circulation in the system, so check the circulating pump. Finally, air in the system can trigger this, so vent the system.
R
ritterphilipAug 27, 2025
What to do if my Fer FERtech F 32 D has poor combustion?
- K
  Kim SimpsonAug 27, 2025
  If your Fer Boiler is experiencing poor combustion, it might be due to an inlet/exhaust flue obstruction. To resolve this, check the flue.
M
michellecarterAug 27, 2025
What to do if my Fer Boiler has poor combustion fault?
- H
  holtnicholasAug 28, 2025
  If your Fer Boiler shows a poor combustion fault, specifically if fault F20 was generated 6 times in the last 10 minutes, refer to fault F20 for guidance.
E
Elizabeth MathewsSep 22, 2025
What to do if my Fer FERtech F 32 D supply voltage is under 180V?
- J
  Jose FordSep 22, 2025
  If the supply voltage to your Fer Boiler is under 180V, it is due to electric mains trouble. Check the electrical system.
P
Pamela HendricksSep 16, 2025
What should I do if my Fer Boiler shows no flame after the ignition phase?
- C
  christophermendezSep 16, 2025
  If your Fer Boiler shows no flame after the ignition phase, it could be due to low pressure in the gas system. Check the gas pressure. Another possible cause is the burner minimum pressure setting, so check the pressures.
K
Kathryn PerezSep 18, 2025
What to do if my Fer FERtech F 32 D has faulty mains frequency?
- E
  Eugene LucasSep 18, 2025
  If your Fer Boiler indicates a faulty mains frequency, it is due to electric mains trouble. Check the electrical system.
E
Elizabeth MitchellSep 7, 2025
What does it mean if my Fer Boiler has a DHW sensor fault?
- L
  lopezjacobSep 7, 2025
  A DHW sensor fault in your Fer Boiler may be due to a damaged sensor. Check the wiring or replace the sensor. It could also be due to wiring shorted or wiring disconnected.
J
James FrancoSep 4, 2025
What does it mean if my Fer FERtech F 32 D has a Delivery sensor 1 fault?
- F
  fcooperSep 4, 2025
  A Delivery sensor 1 fault in your Fer Boiler may be due to a damaged sensor. Check the wiring or replace the sensor. It could also be due to wiring shorted or wiring disconnected.