Ferroli DOMINA F24 N User Manual (English)

Questions and Answers:

C
Christopher BrownAug 20, 2025
How to fix no burner ignition on Ferroli DOMINA F24 N Water Heater?
- M
  moralescaseyAug 20, 2025
  If the Ferroli Water Heater burner fails to ignite, it could be due to several reasons. First, ensure that there is a regular gas flow to the boiler and that all air has been purged from the pipes. Next, inspect the ignition/detection electrode for proper wiring, positioning, and any deposits. Also, verify the gas valve's functionality, replacing it if necessary. Finally, check and adjust the ignition power if it's too low.
M
Michelle FordAug 22, 2025
What to do if there is no flame after ignition phase in my Ferroli DOMINA F24 N?
- J
  Jacob AndrewsAug 22, 2025
  If the Ferroli Water Heater displays no flame after the ignition phase, it could be due to low pressure in the gas system. You should check the gas pressure. Another potential cause is the burner minimum pressure setting, so you should check the gas pressures.
M
Margaret GonzalezAug 25, 2025
How to troubleshoot air pressure switch failure in Ferroli DOMINA F24 N Water Heater?
- B
  Brian ClarkAug 25, 2025
  If the air pressure switch in your Ferroli Water Heater fails to close contacts within 20 seconds of fan activation, begin by checking the wiring of the air pressure switch. Also, check the fan. Ensure the baffle is correct for your unit by checking the pressure switch. If the flue is obstructed or not correctly sized, replace the baffle.
T
thomasbeckAug 26, 2025
Why is the display off on my Ferroli DOMINA F24 N Water Heater?
- P
  Patricia McneilAug 27, 2025
  If the Ferroli Water Heater's display is off, the possible causes are a faulty card, no power, or blown fuses. In the case of a faulty card - card failure. If there is no power, check the power supply. If the fuses are blown, replace them.
C
Christopher JonesAug 28, 2025
What causes air pressure switch contacts closed on activation of fan in Ferroli DOMINA F24 N Water Heater?
- K
  Kristine RodriguezAug 28, 2025
  If the air pressure switch contacts are closed on activation of fan in your Ferroli Water Heater, it could be due to several reasons. Check the pressure switch, fan, and fan socket. Verify the wiring. Make sure the baffle is correct. Inspect the flues to ensure they are the correct length and clean them if obstructed.
A
Angela AllenAug 29, 2025
Why does my Ferroli DOMINA F24 N show flame present signal with burner off?
- U
  upadillaAug 29, 2025
  If the Ferroli Water Heater shows a flame present signal even when the burner is off, the issue might stem from an electrode fault. Check the ionization electrode wiring. Alternatively, there may be a card fault, so you should check the card.
K
Kara HendrixAug 31, 2025
What to do if overtemperature protection intervention in Ferroli DOMINA F24 N Water Heater?
- D
  danielle35Aug 31, 2025
  If the overtemperature protection is intervening in your Ferroli Water Heater, it might be due to a damaged heating sensor. Check the correct positioning and operation of the heating sensor. Another cause may be no water circulation in the system, so check the circulating pump. Finally, air in the system can cause this issue, so vent the system.
S
scalhounSep 2, 2025
How to fix exchanger protection intervention in Ferroli Water Heater?
- G
  Greg WilliamsSep 2, 2025
  If the exchanger protection is intervening (LEDs flash alternately) in your Ferroli Water Heater, it could be due to no system HO circulation. Check the circulating pump. It may also be caused by air in the system, so vent the system.
S
Sarah Bailey MDSep 4, 2025
How to troubleshoot gas valve fault in Ferroli DOMINA F24 N?
- P
  Peter HernandezSep 4, 2025
  If you are experiencing a gas valve fault in your Ferroli Water Heater, first, check the wiring for any disconnections. Also, check the gas valve and replace it if necessary.
E
Erica OnealSep 6, 2025
What does delivery sensor fault mean on Ferroli DOMINA F24 N?
- G
  Gregory WatsonSep 6, 2025
  If your Ferroli Water Heater indicates a delivery sensor fault, the sensor may be damaged. Check the wiring or replace the sensor.