Festo EAMM-A-V...-...A Series User Manual

Translation of the original instructions
1 Applicable documents
All available documents for the product èwww.festo.com/pk.
Observe further applicable documents:
– Motor instruction manual
– Axis instruction manual
2 Safety
2.1 Safety instructions
– Only assemble the product on components that are in a condition to be safely
operated.
– Clean shafts. The coupling hubs[1] grip without slipping only on dry and
grease-free drive shafts.
– Observe proper alignment of the coupling hubs[1]
è 5.1.4 Coupling alignment.
– Support the combination è 5.2.1 Supporting the axis-motor combination:
– if there are far-protruding or heavy motor attachments
– if there are severe vibrations or oscillation/shock loads
– Perform a homing procedure each time after disconnecting or turning the
motor.
– Select required mounting components. The kit contains all the mounting com-
ponents that may be required.
– Observe tightening torques. Unless otherwise specified, the tolerance
is±20%. è 7 Technical data.
2.2 Intended use
2.2.1 Usage
Connecting an axis to a motor in axial configuration to the driven shaft.
2.2.2 Permissible axes and motors
NOTICE!
Overloading can cause malfunction and material damage.
The motor’s output variables must not exceed the permissible values of the com-
ponents used.
Permissible values èwww.festo.com/catalogue.
• Limit the motor’s output variables accordingly.
• Derive the axis and motor from the interface codes.
Example: EAMM-A-V25-40P
V25: axis interface
40P: motor interface
Axis interface Axis
1)
V20 EGSC-BS-25, EPCC-BS-25
V25 EGSC-BS-32, ELGC-BS-32, EPCC-BS-32
V32 EGSC-BS-45, ELGC-BS-45, ELGC-TB-45,
EPCC-BS-45
1) mini slide EGSC-BS, spindle axis ELGC-BS, toothed belt axis ELGC-TB, electric drive EPCC-BS
Tab. 1
Motor interface Motor
1)
28A EMMS-ST-28
28AA Third-party motor
35A EMMB-ST-35, third-party motor
38AA Third-party motor
40P EMMB-/EMME-AS-40
Motor interface Motor
1)
40R Third-party motor
40RA Third-party motor
42A EMMS-ST-42, third-party motor
42AB Third-party motor
57A EMMS-ST-57, third-party motor
58AA Third-party motor
60AA Third-party motor
60P EMMB-/EMME-/EMMT-AS-60, third-party motor
60PA Third-party motor
60RA Third-party motor
1) servo motor EMM...-AS, stepper motor EMM...-ST, motor unit EMCA-EC
Tab. 2
It is the responsibility of users to qualify third-party motors with the matching
mechanical interface for the combination.
You can find out which third-party motors are suitable from your local Festo con-
tact partner or from èwww.festo.com/sp.
2.3 Qualification of specialized personnel
Mounting only by qualified personnel.
3 Additional information
– Accessories èwww.festo.com/catalogue.
4 Scope of delivery
1
Coupling hub (1x)
2
Locking screw (1x)
5
Coupling housing (1x)
10
Screw (4x)
18
Threaded pin (4x)
19
Elastomer spider (1x)
Fig. 1 Scope of delivery
30
Reducing sleeve (4x)
Fig. 2 Addendum with EAMM-U-...-60PA
5 Mounting
5.1 Assembly
5.1.1 Preassembly of reducing sleeve
The reducing sleeves[30] are required with EAMM-A-...-60PA.
Inserting the reducing sleeves
Fig. 3 Insert reducing sleeves
• Insert reducing sleeves[30] into the mounting holes of the motor.
8096408
EAMM-A-V...-...A/P/R-1
Axial kit
8096408
2019-01b
[8096410]
Instructions| Assembly
Festo AG & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com

Festo EAMM-A-V...-...A Series Specifications

General

Brand	Festo
Model	EAMM-A-V...-...A Series
Category	Industrial Equipment
Language	English