FingerTec H3i - User Manual

w w w . f i n g e r t e c . c o mw w w . f i n g e r t e c . c o m
User Guide
H3i
Stand-alone Fingerprint &
Card Access Control System
!
IMPORTANT
This guide serves as an important
document for consumers to operate H3i.
Keep this guide intact for your future
reference.
For any problems, kindly contact support@
fingertec. com for assistance.
VERIFY YOUR ADMIN PASSWORD
Default Password: 1234
Operation: Press * > LED goes off > Buzzer emits
long beep > Press # > Insert the Admin password >
Green LED blinks > Buzzer emits long beep again >
Admin password verified successfully
Note: The admin password must be inserted before the start of
any operation in H3i.
CHANGING ADMIN PASSWORD
It’s recommended that you change the default Admin
password to your very own 4-digit unique password. If
you want to use less than 4 digits, hash (#) symbol is
permitted. I.e.: 123 will be keyed in as 123#.
Operation: Verify default Admin password > Press 8 >
Insert new Admin password > Repeat new Admin
password > Green LED blinks > Buzzer emits long
beep > Admin password changed successfully
H3i assigns user IDs automatically. It ranges from 1 to
65534. Record the details of enrollment using a form
for future reference. Enroll fingerprints and cards as
desired.
ENROLLING FINGERPRINTS
Operation: Verify your Admin password > Press 1 >
Scan finger 3 times > Green LED blinks > Buzzer emits
long beep > Continue to enroll another fingerprint >
Press * to end process

ENROLLMENT
ENROLLING CARDS
Operation: Verify your Admin password > Press 1 >
Wave card once > Green LED blinks > Buzzer emits
long beep > Continue to enroll another card > Press
* to end process
Note: H3i will blink its red LED and it’ll beep twice if the
fingerprint or card data had already been enrolled before or
you registered a bad fingerprint. Ensure the fingerprint
quality before enrollment.
ENROLLING A BATCH OF CARDS
Operation: Verify your Admin password > Press 6 >
Wave the 1st card once > Insert the total number of
cards (i.e. 50) > Press # if the total number is less than
3-digits for example 81#, 99# > Green LED blinks >
Buzzer emits long beep > Press * to end process
Note: All cards must have running card number in
sequence.
SETTING PASSWORDS
H3i supports 8 sets of passwords. Any of the
predefined passwords can unlock the device. Get
ready with the passwords before you register them in
H3i.
For example: SET PASSWORD
1 2331
2 4563
ENROLLING PASSWORDS
Operation: Verify your Admin password > Press 3 >
Green LED blinks > Buzzer emits long beep > Press
the number of password(s) set, e.g. 1 > Insert the
password > Insert the same password again > Green
LED blinks > Buzzer emits long beep again > Press * to
end process
Note: If you want to continue enrolling more passwords, do not
press *, which will end the process. Instead, continue by inserting
the new set number and its new password. Maximum set of
passwords allowed is 8. Press # to fill in the gap if your chosen
password is less than 4-digits. I.e.: 123 will be keyed in as 123#.
©
2015 Timetec Computing Sdn Bhd. All rights reserved • 082015

Summary

Admin Password Management

VERIFY YOUR ADMIN PASSWORD

Verifies the admin password. The default is 1234.

CHANGING ADMIN PASSWORD

Change the default admin password to a new 4-digit unique password.

User Enrollment

ENROLLING FINGERPRINTS

Enroll fingerprints by scanning a finger multiple times.

ENROLLING CARDS

Enroll cards by waving them at the induction area.

ENROLLING A BATCH OF CARDS

Enroll multiple cards sequentially by inputting total count.

Password Enrollment

ENROLLING PASSWORDS

Set up to 8 unique passwords for device access.

User Information Deletion

DELETING USER ID

Delete users by inserting their user ID for deletion.

DELETING FINGERPRINT

Delete enrolled fingerprint by placing it on the scanner.

DELETING CARDS

Delete enrolled cards by waving them at the induction area.

DELETING PASSWORDS

Delete passwords by inserting the set number and new password.

DELETING DEVICE INFORMATION

Delete all device information except stored passwords.

Device Operations and Settings

RESET TO DEFAULT FACTORY SETTINGS

Reset the device back to its default factory settings.

UNLOCK DOOR ADMIN PASSWORD

Use the admin password to unlock doors.

ENABLE;DISABLE LED BLINKS DURING IDLE MODE

Control the blinking behavior of the device's LED during idle mode.

Product Specifications

FingerTec H3i Specifications

General

Brand	FingerTec
Model	H3i
Category	IP Access Controllers
Language	English