What to do if dishes did not dry in Fisher & Paykel Dishwasher?
If your dishes aren't drying in your Fisher & Paykel Dishwasher, make sure they are not nesting together. Also, check the rinse agent levels and refill the dispenser if it's depleted, or increase the rinse agent setting if it's too low. If you used the Eco wash program, try a standard wash program instead.
Why are there water marks on dishes from my Fisher & Paykel Dishwasher?
Water marks on dishes from your Fisher & Paykel Dishwasher can occur if the rinse agent is depleted, so refill the rinse agent dispenser. Another cause could be that the rinse agent setting is too low, in which case you should increase the rinse agent setting. Also, check if the DishDrawer® is overloaded or incorrectly loaded.
How to fix water leaking from Fisher & Paykel DishDrawer DD24 models Dishwasher?
If your Fisher & Paykel Dishwasher is leaking water, first check if the drain hose is disconnected from the waste pipe and reconnect it. Also, ensure the water inlet hose is securely connected. If the leaking persists, turn off the water and power supplies to the DishDrawer®.
What to do if Fisher & Paykel DishDrawer® will not open?
If your Fisher & Paykel DishDrawer® won't open, the Childlock feature or the Closed drawer option might be enabled. To resolve this, turn the Childlock off by holding down the / button until the symbol disappears from the LCD screen or the light above the / button disappears. You can also press the button to open the DishDrawer®.
Why Fisher & Paykel DishDrawer® will not start?
If your Fisher & Paykel DishDrawer® won't start, ensure the power supply is connected.
How to fix excess water in Fisher & Paykel DishDrawer DD24 models Dishwasher?
If there is excess water in your Fisher & Paykel Dishwasher, check the drain hoses for bends or kinks and straighten them.
Why is my Fisher & Paykel DishDrawer® beeping intermittently?
If your Fisher & Paykel DishDrawer® is beeping intermittently, it is likely in pause mode. Close the DishDrawer® and press the button to resume operation.
Why is my Fisher & Paykel Dishwasher foaming?
Foaming in your Fisher & Paykel Dishwasher could be due to using the incorrect amount of detergent, so refer to the detergent section or consult the detergent manufacturer’s instructions. It may also happen if there is too much egg in the wash load, in which case you should increase the amount of detergent. Finally, the rinse agent setting might be too high, so decrease it.
Why is there excessive motor noise coming from my Fisher & Paykel Dishwasher?
Excessive motor noise in your Fisher & Paykel Dishwasher can occur if the filter plate and/or spray arm is incorrectly placed. It can also happen if there's no water in the motor area, which usually occurs on the first use or after the DishDrawer® hasn't been used for a while. In this case, run the DishDrawer®.
General| Product Type | Dishwasher |
|---|---|
| Model | DD24 |
| Number of Drawers | 2 |
| Wash Cycles | Eco, Rinse |
| Features | Delay start, Child lock |
| Width | 60 cm |
| Depth | 57 cm |
| Height | 82 cm |
| Color | Stainless steel |
Essential safety precautions for operating the dishwasher, covering fire, explosion, and personal injury risks.
Procedures and requirements for installing the DishDrawer® safely and correctly.
Instructions for cleaning and upkeep of the dishwasher to ensure optimal performance.
Guidelines and precautions for the safe and effective operation of the dishwasher.
Controls the power on/off function of the dishwasher.
Starts, pauses, or restarts a wash program.
Instructions for properly loading dishes into the dishwasher for optimal cleaning.
Guidance on adding the correct type and amount of detergent.
Steps for choosing the appropriate wash cycle for the load.
Crucial warnings and recommendations regarding detergent use.
Common causes and solutions for dishes not coming out clean.
Troubleshooting steps for water leaks from the dishwasher.
Solutions for when the dishwasher drawer cannot be opened.
How to identify and understand fault codes displayed by the dishwasher.
Steps to take when a fault code appears, including troubleshooting.
Checks to perform before contacting service for issues.
To Next Page