Fisher & Paykel DishDrawer DD24ST Series - Product Dimensions; Cabinetry Dimensions

23
PRODUCT DIMENSIONS CABINETRY DIMENSIONS
A
B
C
E
D
F
G
H
J
Prefinished Flat door &
Integrated models for
18 ⁄”(480mm) cavity
Prefinished LCD models &
Integrated models for
17 ⁄”(456mm) cavity
K
Product dimensions (inches (mm))
Pre nished
LCD **
DD24ST
Pre nished
Flat door
DD24ST
Integrated
17 ⁄” (456 mm) cavity**
DD24ST
Integrated
18 ⁄” (480 mm) cavity
DD24ST
A
overall height* of product (incl. drawer front height)
17 ⁄” (453) 18 ¾ ” (477) 17 ⁄” (453) 18 ¾ ” (477)
B
overall width of product
23 ⁄”(599) 23 ⁄”(599) 23 ⁄”(599) 23 ⁄”(599)
C
overall depth of product (excl. curvature/handle)
22 ⁄” (570) 22 ⁄” (570)
22 ⁄”
(570)
***
22 ⁄”
(570)
***
D
depth of drawer (open) (excl. curvature/handle)
21 ⁄” (538) 21 ⁄” (538) 21 ⁄” (538) 21 ⁄” (538)
E
height* of chassis
17 ⁄” (453) 17 ⁄” (453) 17 ⁄” (453) 17 ⁄” (453)
F
depth of chassis (incl. trimseal)
21 ¾ ” (552) 21 ¾ ” (552) 21 ¾ ” (552) 21 ¾ ” (552)
G
depth of drawer front panel (excl. curvature/handle)
⁄” (18) ⁄” (18) ⁄” (18) ⁄” (18)
H
depth of curvature or handle
⁄” (11) 1 ⁄” (41) n/a n/a
I
height of drawer front
17 ¼ ” (438) 18 ½ ” (470)
17 ⁄” (442)
min
18 ½ ” (470)
min
J
height of venting area at base of product
¼ ” (7) ⁄” (9) ⁄” (9) ⁄” (9)
K
height of installation bracket slots (on top of chassis)
⁄” (2) ⁄” (2) ⁄” (2) ⁄” (2)
*Chassis heights include bracket slots **In these instances, you would skip step 7 ***Panel thickness - ⁄” (18 mm)
Note: for Pre nished Flat door models, the height from the top of handle to the top of door - 2
½ ” (64 mm)
I
Installation diagrams for illustration purposes only
A
A
B
C
Cabinetry dimensions (inches (mm))
Pre nished
LCD
DD24ST
Pre nished
Flat door
DD24ST
Integrated
17 ⁄” (456 mm)
cavity
DD24ST
Integrated
18 ⁄” (480 mm)
cavity
DD24ST
A
inside height of cavity
17 ⁄” (456) 18 ⁄” (480) 17 ⁄” (456) 18 ⁄” (480)
B
inside width of cavity
23 ⁄” (600) 23 ⁄” (600) 23 ⁄” (600) 23 ⁄” (600)
C
inside depth of cavity (inside)
22 ⁄” (580) 22 ⁄” (580) 22 ⁄” (580) 22 ⁄” (580)
K
F
C
H
Installation diagrams for illustration purposes only
⁄” (2.5 mm)
⁄” (2.5 mm)
½
” (13 mm)
Minimum clearances (inches (mm))
Cavity height options for Integrated models:
To match existing kitchen cabinetry or the height of other
appliances installed next to DishDrawer, you may choose to
install DD24ST Integrated models into either a
17 ⁄” (456 mm) or a 18 ⁄” (480 mm) high cavity.
Note: the minimum height of the custom drawer front
panel will also be different for these two options.
(1,2) -1- 599754C DD24S TALL installA2 USCA.indd 15/4/09 2:34:15 PM
(1,2) -1- 599754C DD24S TALL installA2 USCA.indd 15/4/09 2:34:15 PM