Fisher RS-1060 - Disassembly Instructions; Chassis and Front Panel Removal; Circuit Board Removal; Specific Component Removal

o
Removal
of
Ghasis from Cabinet
1. Remove 6 screws
from
le{t and
right sides of cabinet.
2.
Separate cabinet
from
chassis.
3. Remove 18 screws from bottom of cabinet.
4. Remove
4
screws
from
Leg.
5.
Separate bottom of cabinet
from
chassis.
Removal
of
Front
Panel
Assembly
1. With Allen
wrench remove Tuning
and
Volume Knobs.
2.
Remove
all
Knobs
and
Lever
switches
f rom
panel.
3.
Remove 2
screws
from
top of
panel.
4. Remove 2 screws
from
bottom of
panel.
5.
Remove
nut from
"Function"
and
"Speaker"
switches
located on
Front Panel Assembly.
6. Separate
Front
Panel
Assembly
from
chassis.
Removal of Slide
Rail Pointer
1. Remove
Metal
Slide
Pointer
from
Slide
Rail
Pointer.
2.
Remove 3 screws from
top of Slide
Rail
Pointer.
3.
Remove 2
screws
from left
and
riqht
sides of Slide
Rail
Pointer.
Removal
of
Meter
1. Remove One screw and
Meter
Cover.
2. Unsolder
leads f rom meter
terminals.
3.
Grasp
Meter firmly
and
pull
back separating
Meter from
oanel.
Removal of AM-FM Stereo
Function
Indicator
Lamps
1. Grasp
base
of lamp with long-nosed
Pliers
and Carefully
extract from
grommet
holder.
2. Unsolder
AM-FM Indicator
Lamo
from
P.C.
Board.
Removal and Replacement
of
Dial Lampc
1.
Remove 4
plastic
screws
from
top
of Dial
P.C.
Board.
2.
Grasp
Dial
Lamp and extract
from
lamp
grommet
holder.
Removal
of
Front End
from
Chassis
1. Unsolder leads from
Front End
terminal.
2. Unscrew 2 screws
from
Drum.
(Do
Not Remove Dial
String
From
Drum.)
3. Remove 4
screws
from
insides of
Front End.
(Do
Not
Remove 4
screws
From
Outsides Of
Front End
Case.)
Testing and troubleshooting any of the
P.C.
boards
does
not
require
removal
since all iomponent
parts
are top
board
mounted. For
underneath
board
inspection
purposes
or
r-ri,:,, =
.iei,:;i;;l
:::i^ipalcar
is
:,-'
i-,rnsnl,lcr;J an{1
replaced,
the
P.C.
board can be sufficiently turned
over
by
only
removing
the
hold down hardware.
Where it neces-
sitates
complete
removal
of
any
individual
board
then
oroceed as
follows.
DISASSEMBLY
INSTRUCTIONS
Remoual
of AM-FM
RF/lF/TtlPX Amp
P.C. Board
1. Urisolder
wire wraps
from
terminals.
2.
Remove 4
screws
from
P.C.
Board.
3. Slide
P.C.
Board
from
plastic
clip.
Removal
of Multi
Path
and Dolby
P.C.
Board
(RS-1080
Only)
1. Unsolder
wire wraps
from
terminals.
2.
Remove 4 hold
down screws.
Removal
of EO-Amp P.C. Board
1. Unsolder
wire wraos from terminals.
2.
Remove 4
Hold
down screws.
3.
Grasp
P.C.
Board
and
extract
from Shield Case.
(Do
Not Remove
Shield Case
From
Chassis.)
Removal of
Protector P.C. Board
1. Unsolder
wire wraps from
termianls.
2. Remove
4 hold
down screws.
Removal
of
Volume
lnd and
Volume
P.C.
Board
1. With Allen
wrench remove Volume Ind
P.C.
Board
from
Volume
Shaft.
2.
Remove
One
nut holding Volume
P.C.
Board.
3. Unsolder
wire wraos from
terminals.
Removd of
Pre
Amp
P.C. Board
1.
Remove
14 screws
from
7
Lever
Switches.
2. Unplug 2
connectors.
3. Unsolder
wire wraps from
terminals.
Removal
of
Tone
Control Amp
P.C. Board
1. Remove 3 hold down nuts from Tone Control
P.C.
Board.
2.
Unplug 2 connectors.
Removal
of
Low Range P.C. Board
1.
Remove
2
hold
down nuts from Low Range
P.C.
Boarcj.
2.
Unplug
One connector.
Removal
of
Porver
Supply
P.G.
Board.
'l
.
Remove
2 screws releasing
clip
holding
P.C.
Board.
2. Grasp
P.C.
Board
firmly
and
extract
from
plug.
(Do
Not Remove Plug From
Chassis.)
Removd
of Porver
Amp
P.C.
Board
r
Please
refer
to
Exploded View
on
Page
8.
..
I
I
-5-