flamco Flexcon M-K Series User Manual

1
&LAMCO
M-K Compressor Expansion Automat
Installation and operating instructions
Dear Customer,
Thank you for purchasing the FLEXCON M-K Compressor Expansion Automat – a quality product
from Flamco. This expansion automat from the proven M-K series offers you reliability, guaranteed
operational readiness and ease of use.
On the following pages we will present you with technical specifi cations, instructions and
explanations that facilitate safe use in accordance with regulations. Persons responsible for
transport, installation, commissioning, re-starting; operation, maintenance, checks and repairs
must have read and understood these instructions.
Please place these instructions in a place where they can be inspected at any time.
We will be happy to answer any questions that are not covered by these instructions,
Contents
(Sections 1 – 7 belong together, not independent) Page
1. Exclusion of liability 2
2. Acceptance of goods 2
Inspection 2
T
ype plate 2
Transport 2
Storage 3
3. Product description 3
Methodology 3
Equipment 3
Operating modes 5
Accessories, additions 6
4. Safety instructions 7
Intended area of use 7
Measures for hazard-free operation directions for safe use 8
Avoiding excessive pressure 8
Avoiding excessive temperature 8
Residual hazards 8
5. Installation 9
Environmental conditions 9
Base and setup 9
System connection 9
Gas compartment couplings 10
Electrical installation 10
6. Start 10
Commissioning 10
Pr
ogramming 11
Start and system temperature 11
Re-start 12
7. Maintenance 12
8. Periodic testing, pressure equipment 12
Appendices
Appendix 1
Technical data, specifi cations, hydraulic and pneumatic equipment
Dimensions, weights 13
Minimum distances 14
Example installations 15
Appendix 2
Technical data, specifi cations, electrical equipment
Modules 19
Flexcon control unit, M-K/S,
Operating mode menu. [Fault displays] 20
Programming mode menu 21
Service programming mode [Default settings] 22
Standard terminal diagram 23
Standard terminal diagram, accessories, additions 24
Terminal diagram for special version [400/230V 3/PE ~50Hz] 25
Terminal diagram for special version, accessories, additions [400/230V 3/PE ~50Hz] 26
SDS controller, M-K/U,
Operating mode menu 27
Programming mode menu. 28
Service programming mode. [Default settings] 30
Error list 30
Standard terminal diagram. 31
Standard terminal diagram, accessories, additions 32
Terminal diagram for special version, accessories, additions [Valve pressure increase] 33
Terminal diagram for special version [400/230V 3/PE ~50Hz] 34
Terminal diagram for special version, accessories, additions [400/230V 3/PE ~50Hz] 35
35
Edition 0206© Flamco
Taste ESC drücken
Fehler ablesen
mit Taste RET
Hinweise
Fehler
steuerautomat
0
987
654
321
Nach Fehlerbeseitigung
RETESC
Flamco
electronic control unit
standard pressure control
enter
press
D
SDS
0,025
Taste ESC drücken
Fehler ablesen
mit Taste RET
Hinweise
Fehler
steuerautomat
0
987
654
321
Nach Fehlerbeseitigung
RETESC
0,0250,025
0,025
Flamco
D
SDS
electronic control unit
standard pressure control
enter
press
Taste ESC drücken
Fehler ablesen
mit Taste RET
Hinweise
Fehler
steuerautomat
0
987
654
321
Nach Fehlerbeseitigung
RETESC
18502426 broch Flexcon M-K_UK.indd 118502426 broch Flexcon M-K_UK.indd 1 13-07-2006 08:55:2113-07-2006 08:55:21
www.flamco.nt-rt.ru

flamco Flexcon M-K Series Specifications

General

Brand	flamco
Model	Flexcon M-K Series
Category	Control Systems
Language	English