MONOLIGHT 320M/620M/1220M AC/DC
Safety Precautions:
1. Before using the light, make sure that the electrical
outlet of your local power supplier matches the power
regulation
indicated on your lighting equipment.
2. Do not use any power supply other than the AC
specification indicated on your equipment.
3. Do not expose your lighting equipment to sunshine,
moisture, dust, dirt, rain, or water.
4. Any exposure to chemical solutions, gasoline, grease,
oil, paint, or detergents can result in permanent dam-
age to your equipment.
5. Do not insert metal parts into any lighting equipment.
6. Dry your hands before handling the equipment, as
touching your equipment with wet hands is dangerous
to both the equipment and to you.
7. Do not keep the power on when the light is not in use.
8. Do not attempt repairs to your lighting equipment
personally. If a problem arises, contact the store from
which you purchased the light.
9. This flash has an over frequency protection circuit, rap-
id continuous firing of your flash will cause an audible
alert. continued rapid firing after audible alert will cause
the flash to cease operation and trigger a “cool down”
period of approximately of 10 seconds. after this period,
the flash will resume operation. You may also reboot
the flash by cycling the power off and then on.
Light Body & Back Control Panel
(1) Power Inlet Include Fuse
(2) Power Selection AC DC
(3) Synch Cord Socket
(4) On/Off Switch for Modeling Lamp
(5) On/Off switch for recharge read y-beeper/
Modeling lamp off
(6) Recharge Ready-Light
(7) Slave Sensor
(8) Handle Grip
(9) Locking/Releasing Bolt for Reflector& Soft
Box Connector
(10) On/Off Switch for Sensor
(11) Test Button
(12) Output Power Setting: flash/ modeling lamp
(13) Handle for Angle Adjustable
(14) Stand Mounting
(15) Stand Mounting Bolt
(16) Umbrella Holder
(17) Replaceable Flash Tube
(18) Modeling Lamp
(19) Cable Socket (DC inlet)
Model FP320M FP620M FP1220M
1 Maximum Watt Seconds 150 ws 300 ws 600ws
2 Guide Number 118 ft 192 ft 230 ft
3 Flash Duration 1/600 to 1/1000 1/600 to 1/1000 1/600 to 1/1000
4 Flash Variability Stepless Control from Full Stepless Control from Full Stepless Control from Full
Power to 1/32 Power Power to 1/32 Power Power to 1/32 Power
5 Recycling Time 0.5 - 1 Second <1.5 Seconds <3 Seconds
6 Recycling Time - Battery <1.5 Seconds <3 Seconds <6 Seconds
7 Recycle confirm Yes Yes Yes
8 Flash Ready Indicator Ready Light & Audio Signal Ready Light & Audio Signal Ready Light & Audio Signal
9 Modeling Light Wattage 100 watts 150 watts 250 watts
10 Color Temperature 5600° K +- 5600° K +- 5600° K+-
11 Modeling Bulb Base E26 - E27 E26 - E27 E26 - E27
12 User replaceable flashtube yes yes yes
13 Built-In Slave Yes Yes Yes
14 Slave Sensitivity 30ft. Radius,360 Degree 30ft. Radius,360 Degree 30ft. Radius,360 Degree
15 Synch Terminal Yes Yes Yes
16 Synch Terminal Type 1/4" (6.35 mm) Phono Sync Terminal 1/4" (6.35 mm) Phono Sync Terminal 1/4" (6.35 mm) Phono Sync Terminal
17 Synch Voltage 5.6 5.6 5.6
18 Voltage Stabilization 110-130 ac +/- 0.5% 110-130 ac +/- 0.5% 110-130 ac +/- 0.5%
19 Fan Cooled No Yes Yes
20 Test Button Yes Yes Yes
21 Fuse 8A 10A 10A
22 Reflector/Removable 8" inch 8" inch 8" inch
23 Mount Flashpoint Flashpoint Flashpoint
24 Housing Type Rugged Metal Housing Rugged Metal Housing Rugged Metal Housing
25 Dimensions L 11" W 5.6" H 7.5" L 15" W 5.6" H 7.5" L 15" W 5.6" H 7.5"
26 Weight 3 Lbs (1.7kg) 4-1/2 Lbs (2.4kg) 7 Lbs (3.2kg)
16
15
14
13
14
13
2
4
6
5
8
12
7
3
11
10
9
1
17
18
9
POWER
MODEL
FULL
DIM
SOUND
TEST
SENSOR
DC
AC
SYNC
FUSE 10A
READY
OFF
19
To Next Page
Need help?
General
