Flex innovations RV-8 60E G2 SUPER PNP

Questions and Answers

R
riverajustinAug 13, 2025
What to do if control surfaces are nonresponsive on my Flex Innovations Toy?
- A
  Austin GarciaAug 13, 2025
  If the control surfaces on your Flex Innovations Toy are not responding, there could be several reasons: * Check for any damage to the airframe or control linkage system and repair or replace components as needed. * Inspect wires and connections for damage or looseness, replacing as necessary. * Ensure the transmitter is correctly bound, the correct model memory is active, and the Aura data input configuration and transmitter settings are correct. Consult the radio manual for binding and model selection instructions. * Check the battery voltage with a voltmeter and recharge or replace the battery if necessary. * Ensure the battery is connected to the ESC. * The BEC (battery elimination circuit) or servo may be damaged, requiring ESC or servo replacement.
M
Melanie DunnAug 17, 2025
Why is my Flex Innovations Toy having reduced flight time?
- C
  Cheryl JohnstonAug 17, 2025
  If your Flex Innovations Toy experiences reduced flight time or seems underpowered, consider the following: * Ensure the battery is fully charged before installation. * Verify the propeller is installed correctly, with the convex side facing forward (tractor configuration). * Replace a weak or damaged battery with a new one. * Warm the battery packs to approximately 70°F/21°C before flight if the ambient temperature is too cold. * Use a battery with adequate capacity and discharge capability. * Recharge the flight battery or reduce flight time if the ESC is reaching its low-voltage cutoff. * Use a battery with a higher 'C' rating if the current battery's discharge rating is insufficient.
R
Renee SmithAug 21, 2025
How to fix a non-responsive motor with no ESC initialization tones on Flex Innovations Toy?
- C
  Crystal PayneAug 21, 2025
  If your Flex Innovations Toy motor isn't responding and you don't hear the ESC initialization tones, it might be due to the throttle not being at idle or the throttle trim being too high. Lower the throttle stick and trim completely. If the issue continues, make sure the sub-trim and travel adjust are properly configured in your radio's programming. Also, make sure the motor is correctly connected to the ESC by checking that the plugs are fully seated. Inspect the battery and plugs for any damage, and replace damaged components; do not attempt to repair them.
A
Anna WallaceAug 25, 2025
Why is there excessive propeller noise and vibration in my Flex Innovations Toy?
- P
  powellmatthewAug 25, 2025
  If you're experiencing excessive propeller noise or vibration with your Flex Innovations Toy, check the following: * Replace any damaged spinner, propeller, collet, or motor components. * Balance or replace the propeller. * Tighten the prop nut with the correct wrench. * Ensure the spinner is fully in place and tightened by loosening the spinner bolt, adjusting as needed, and retightening. * Replace the propeller nut or propeller shaft if the threads are not cut straight.
R
rachel91Aug 28, 2025
What to do if the motor turns in the wrong direction on Flex Innovations Toy?
- K
  Kevin DunnAug 29, 2025
  If the motor of your Flex Innovations Toy is turning in the wrong direction, it's likely that the three motor wires are incorrectly connected to the ESC. To fix this, swap any two of the motor wires.
W
wgonzalesSep 1, 2025
What to do if the motor is non-responsive but throttle calibration tones are received on Flex Innovations Toy?
- J
  Jerry StanleySep 1, 2025
  If the Flex Innovations Toy motor is non-responsive but you are receiving throttle calibration tones, the throttle channel is likely reversed. Correct this by reversing the throttle channel in your radio programming.
M
millerdennisSep 4, 2025
Why are there trim changes between flight modes on my Flex Innovations Toy?
- M
  Melissa McbrideSep 4, 2025
  If you observe trim changes between flight modes on your Flex Innovations Toy, it might be because the trims or sub-trims are not properly zeroed. Readjust the control linkage and re-center the trims in the radio. Remove sub-trim and adjust the servo arm or clevis to achieve proper geometry. Also, the transmitter might not be properly calibrated, meaning the aileron, elevator, and rudder are not neutral when the sticks are centered. Calibrate the transmitter or return it to the manufacturer for calibration. Finally, ensure the gyro kill switch is set up on the transmitter by assigning CH7/Aux2 to a two-position switch, following the transmitter configuration guide.

Flex innovations RV-8 60E G2 SUPER PNP Specifications

General

Wingspan	60 in (1524mm)
Construction	Balsa and Plywood
Covering	UltraCote
Assembly Required	Yes
Servos	6 x
Recommended Battery	6S 4000-5000mAh LiPo
Radio System	6+ Channel
Skill Level	Intermediate