ENVIRONMENTAL INFORMATION
Husqvarna UK Ltd. products are manufactured under
an Environmental Management System (ISO 14001)
using, where practical, components manufactured in the
most environmentally responsible manner, according to
company procedures, and with the potential for recycling
at the end of the products’ life.
• Packaging is recyclable and plastic components have
been labelled (where practical) for categorised recycling.
• Awareness of the environment must be considered
when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging indicates
that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative
consequences for the environment and human health,
which could otherwise be caused by inappropriate waste
handling of this product.
For more detailed information about recycling of this
product, please contact your local council ofce, your
household waste disposal service or the shop where you
purchased the product.
GUARANTEE AND GUARANTEE POLICY
If any part is found to be defective due to faulty
manufacture within the guarantee period, Husqvarna UK
Ltd., through its Authorised Service Repairers, will effect
the repair or replacement to the customer free of charge
providing:
a. The fault is reported directly to the Authorised
Repairer.
b. Proof of purchase is provided.
c. The fault is not caused by misuse, neglect or faulty
adjustment by the user.
d. The failure has not occurred through fair wear and
tear.
e. The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorized
by Husqvarna UK Ltd.
f. The machine has not been used for hire.
g. The machine is owned by the original purchaser.
h. The machine has not been used outside of the country
for which it was specied.
i. The machine has not been used commercially.
• This guarantee is additional to, and in no way diminishes
the customers statutory rights.
Failures due to the following are not covered, therefore, it
is important that you read the instructions contained in this
Operator’s Manual and understand how to operate and
maintain your machine.
Failures not covered by guarantee
• Replacing worn or damaged blades.
• Failures as a result of not reporting an initial fault.
• Failures as a result of sudden impact.
• Failures as a result of not using the product in
accordance with the instructions and recommendations
contained in this Operator’s Manual.
• Machines used for hire are not covered by this
guarantee.
• The following items listed are considered as wearing
parts and their life is dependent on regular maintenance
and are, therefore not normally subject to a valid
warranty claim: Blades, Electric Mains cable.
a CAUTION! Husqvarna UK Ltd. does not accept
liability under the warranty for defects caused in
whole or part, directly or indirectly by the tting of
replacement parts or additional parts that are not
either manufactured or approved by Husqvarna
UK Ltd., or by the machine having been modied
in any way.
TECHNICAL DATA
Type Hover Vac 250, Hover Vac 260, Hover Vac 270
Width of Cut (cm) 25 (Hover Vac 250), 26 (Hover Vac 260), 27 (Hover Vac
270)
Speed of rotation of cutting device (rpm) 7000 ± 5%
Cutting height (mm) 10-30
Grass collector capacity (L) 15
Power (kW) 1.4 ± 5%
Measured Sound Power LWA (dB(A)) 93.3
Guaranteed Sound Power LWA (dB(A)) 96
Sound pressure LpA (dB(A)) < 90
Uncertainty KpA (dB(A)) 3.0
Hand / arm vibration avhw (m/s
2
) 2.2
Uncertainty K of ah (m/s
2
) 1.5
9
To Next Page
Loading...
Need help?
General
