15
Instructions
遥控产品规格
Trouble
故障现象 可能原因 解决方法
Check the settings. Set D/R, EPA, ATL to
100% or turn the knobs to maximum
value. Set TRIM to 0 or turn the knob to its
neutral position.
Possible Reason Solution
The motor suddenly stops running
while in working state.
电机转动过程中，突然停转。
After power on, motor can’t work, no
sound is emitted, and LED is off.
通电后指示灯不亮，不自检，无鸣音。
After power on, motor can’t work; red
LED blinks.
通电后红色LED 闪烁，电机无法启动。
The car runs backward while giving
throttle. (The motor runs in the
opposite direction.)
The car can't reach full speed, the
accelerator is maxed out,the red light
is not always on.
遥控器做前进操作，车子反而倒退 。
The car can’t go backward.
车子无法达到全速，油门打到最大，
红灯不恒亮。
The car can’t go forward, but can go
backward.
车子无法倒车。
车子正向加油不走，反向倒车却行走。 遥控器油门通道方向设置错误。
1.The ESC doesn’t get its working voltage;
Connections between battery pack and
ESC are broken. 2.Switch is damaged.
1. 电调没有得到工作电源。2. 电调开关损坏。
1.Check the battery wires connection or
replace the defective connectors.
2.Replace the switch.
1. 检查电池到电调的电源输入通路是否有焊
接不良情况，并重新焊好。2. 更换电调开关。
1.Throttle signal is abnormal. 2.Automatic
throttle range calibration is failed.
1. 电调油门线插反或通道插错。2. 电调无法
完成油门自检校调。
1.Check the throttle wire connection; make
sure it is plugged into the throttle channel
of the receiver. 2.Set the “TRIM” of throttle
channel to 0 or turn the knob to its neutral
position.
1. 将电调的油门排线按正确方向插到接收机
的油门通道（Throttle, 通常为CH2）。2. 将
遥控器的油门通道的中点微调 “TRIM”调
为0 或相应旋钮调到中点位置。
The wire connections between ESC and
the motor need to be changed.
遥控器油门通道方向设置错误或马达接线错误。
Swap two wire connections between
the ESC and the motor.
交换 ESC 和电机之间的两个电线连接。
Reset the direction of throttle channel from
original “NOR” to “REV”, or from original
“REV” to “NOR”.
遥控器设置错误。
The direction of throttle channel is not
correct.
1. 将遥控器油门通道的 “D/R” 、 “EPA”
、“ATL” 等参数调到100%或相应旋钮调
到最大位置， 油门通道的中点微调“TRIM”
调为0 或相应旋钮调到中点位置。
The direction of throttle channel is not
correct.
1. 将倒车选项跳线帽插入正确位置。2. 将遥
控器的油门通道的中点微调 “TRIM”调为
0 或相应旋钮调到中点位置。
1.Check the jumper and plug it to the
correct position. 2.Set the “TRIM” of throttle
channel to 0 or turn the knob to its neutral
position.
1. 油门信号丢失。2. 电调进入电池低压保护
或过热保护状态。
1.The throttle signal is lost. 2.Low voltage
cut-offprotection or Over-heat cut-off
protection has been activated.
1. 检查遥控器电池电压是否过低。2. 电调
红灯闪烁表示低压或过热保护，请更换电池
组或检查电调温度。
1.Check the transmitter and the receiver.
2.Replace the battery pack, or cool down
the ESC.
将遥控器油门通道反向换，从原 “NOR”
换为“REV”或从原”REV”换为 “NOR”。
1.The jumper position is wrong. 2.The
neutral point of throttle channel is changed
or drifted.
1. 倒车选项跳线帽位置错误。2. 油门中点偏
移。
To Next Page
Loading...
