FMX TD200 Series - User Manual

Customer is solely responsible for validating application, operation,
maintenance, and code compliance and other information and data
relating to the installation, operation, safety, and maintenance of all
components. There is no guarantee that this information is suitable for
your application, nor is there any manufacturer/supplier assumption of
responsibility for your product design, installation, testing, or operation.
Information herein is provided “as is” with no guarantee of any kind. Every
attempt has been made to ensure the accuracy and reliability of the
information provided in this document.
Check the label affixed to the side of the drive and make sure the
input and output power specifications match the available power
source and motor.
PRODUCT: E510-2P5-H-U MOTOR RATING: 0.5 HP
INPUT : AC 3PH 200-240V (+10%,-15%) 50/60Hz 4A
OUTPUT : AC 3PH 0-599 Hz 2.6A IP20/NEMA 1
ENCLOSURE : IP20
P/N BARCODE S/N BARCODE
TD200-20P5-3PH
1
2

4
5
4.8” / 12cm
2” / 5cm
4.8” / 12cm
2” / 5cm
Enclosure

Cooling Fan
Vent
Operating
Temperature:
-10°C - +50°C (14-122 °F)
If AC Drive is placed in an enclosure, provide
additional cooling and ventilation to maintain
ambient temperatures below 50°C
(
122 °F
)
AC Drive Label
Minimum Spacing Requirements
Adequate thermal management is key to extending the life of the AC
drive. Overheating and excessive dust/debris will shorten the life of
the drive significantly.
Identify Drive Specifications

Enclosure
Cooling Fan
2” / 5cm
Vent
1 Verify receipt of proper drive model
2 Verify Input Power
3 Provide adequate circuit provision
• Ensure proper wire size
• Provide proper circuit protection
• Comply to all local codes and regulations
4 Output Amperage
• Ensure output is adequate to meet the full load amps of the
motor or application
5 Verify Environment
• Provide proper environmental protection
• Install drive in a clean and cool environment protected from
contaminants and debris
QUICK START
GUIDE
STEP 1
Mounting/Spacing Requirements
STEP 2
Applicable Models:
• 120V (1PH): 0.25 – 1HP
• 240V (1PH): 0.25 – 3HP
• 240V (3PH): 0.5 – 3HP
• 480V (3PH): 1 – 3HP
CAUTION
Installation and wiring must be performed by qualified personnel
Do NOT remove any protective covers or attempt any wiring while input
power is applied. Connect all power wiring and control wiring before
applying input power. Always turn OFF the power supply before
attempting AC Drive installation and terminal wiring.
Internal capacitors hold a charge after power supply has been removed.
After disconnecting power, wait at least 10 minutes before touching any
wiring, circuit boards, or components.
Check all wiring to ensure all connections are correct after installation of
AC Drive and any other devices. Failure to comply could result in serious
injury, death, fire, or damage to the AC Drive.
Do not use an improper voltage source. Failure to comply could result in
in serious injury, death, fire, or damage to the AC Drive. Verify the rated
voltage of the AC Drive matches the voltage of the incoming power
supply before applying power.
Do not connect a contactor or switch in series with the AC Drive and the
motor.
WARNING
This document is intended to provide a short guide on the installation
and setup of a FMX Tough Drive. Refer to the user manual for all safety
precautions and further details regarding installing, wiring, operating,
servicing, or inspecting the AC Drive.
NOTE
TD200-QS

Summary

Identify Drive Specifications

Verify Drive Model and Input Power

Check drive label for model, input power, output specs, and ensure adequate circuit provision.

Verify Output Amperage and Environment

Ensure output meets motor load and install drive in a clean, cool, protected environment.

Mounting and Spacing Requirements

Minimum Spacing Requirements

Details required clearances around the enclosure for cooling and ventilation.

Operating Temperature Guidelines

Specifies operating temperature range and enclosure cooling needs.

Wiring the AC Drive

Power Terminal Descriptions

Explains the function of power input and output terminals L1, L2, L3, T1, T2, T3, P, BR.

Wiring Diagrams for Input Models

Illustrates wiring connections for 1PH and 3PH input models.

Control Circuit Terminals

Details multi-functional digital inputs, external analog inputs, relay output, and analog output.

Commonly Used Parameters

Command and Frequency Source Parameters

Covers parameters for main run command, external terminal modes, and frequency command source.

Speed and Timing Parameters

Details parameters for frequency limits, acceleration/deceleration times, and stop mode.

Motor Configuration Parameters

Covers Volts/Hz patterns and rated motor current settings.

Check Motor Direction

Motor Direction Test Procedure

Steps for testing motor rotation direction using the AC Drive keypad.

Motor Direction Correction

Instructions on how to correct motor rotation by swapping output leads.

Set Motor FLA

Example Motor Nameplate Details

Illustrates typical information found on a motor nameplate for drive setup.

Setting Motor Full Load Amps

Procedure for entering the motor's Full Load Amps (FLA) into the drive.

Set Accel.; Decel. Times

Set Main Command Source

Configure Main Command Source

Sets parameter 00-02 to select keypad or external terminal control.

Configure Operation Modes

Sets parameter 00-04 for different external control modes (FWD/REV, RUN/STOP, 3-wire).

Configure Speed Potentiometer

Sets parameter 00-05 for external analog signal input (AVI) for speed control.

FMX TD200 Series Specifications

General

Communication Interface	RS-485, Modbus RTU
Output Current	Up to 200A
Control	Digital
Feedback	Tachometer
Operating Modes	Speed, Torque
Protection	Overcurrent, Overvoltage, Overtemperature, Short Circuit
Cooling Method	Forced Air