Fostex X-28H - Transport and Display Functions

D MONITOR LEVEL CONTROL
(MONITOR)
Determines the overall output level sent to the MON
OUT jacks @ and PHONES jack
(§ RECORD TRACK SELECT SWITCHES
(REC SELECT)
These three-position switches select the track(s) to be
recorded. Setting the switch to the numbered position
(1,2,3 and 4) selects the respective tape tracks; these
are direct record settings that bypass the PAN and EQ
controls. Setting the switch to the center position dis¬
ables recording. Setting it to L (left) or R (right) selects
the respective signal of the stereo buss for recording.
The signal is recorded to the track number indicated on
the switch. (For example, if the first REC SELECT
switch is set to L, the left signal of the stereo buss will
be recorded to track 1.) This setting is particularly
useful for recording multiple inputs sent on the stereo
buss to a single track.
© REHEARSAL SWITCH
(REHEARSAUMSHM)
This switch is used for disabling/enabling recording
during punch-in recording. It also lets you hear the
punch-in and punch-out as you rehearse, without eras¬
ing the original track. (Rehearsal mode is effective only
when in the high speed mode and does not function in
normal speed.) The [REHEARSAL] indication in the
display lights up when in the rehearsal mode. The tape
speed can be switched from high speed to normal by
simultaneously pressing the rehearsal key and the
ST OP/ button @ when the transport is stopped.
(The [REHEARSAL] indication in the display flashes.)
To switch back to high speed, simply press the RE¬
HEARSAL switch.
© DOLBY* B NOISE REDUCTION SWITCH
(DOLBY NR)
This switch turns the Dolby B noise reduction system
on and off. The switch does not lock and is switched on
and off each time it is pressed. Check whether the
Dolby B noise reduction is on or off from the [DOLBY
IN] indication in the display; it lights up when on, and
goes out when off.
Dolby is set to on as a default power-on setting to give
you the best possible recording and playback quality.
(© COUNTER RESET SWITCH
(COUNT RESET)
Pressing this button resets the tape counter © - b to
“ 000 . ”
® RECORD BUTTON
(REC)
Pressing this button (after the REC SELECT switches
© have been properly set) allows you to monitor the
level of the input with the bar graph level meters © - a.
(Pressing the REC button alone does not actually start
recording, however. To record, hold down the REC
button and simultaneously press PLAY.
Note: Recording can also be started. During play¬
back, hold down the REC button and simulta¬
neously press PLAY; if the REC SELECT
switches have been properly set, recording will
start.
© PLAY BUTTON
(PLAY)
CD REWIND BUTTON
(REWIND)
© FAST FORWARD BUTTON
(F. FWD)
i) STOP BUTTON
(STOp/ ^ ann )
This button stops the transport. The tape speed can be
switched from the high speed to the normal speed by
simultaneously pressing this button and the RE¬
HEARSAL/S§lliIM] switch © when the transport
is stopped.
@ ZERO RETURN BUTTON
(0 RTN)
Pressing this button rewinds or fast forwards the tape
to the “000” position. (The zero return indicator in the
display (»0 or 0^) will light.) This function, used with
the COUNT RESET switch ©, makes it easy to “mark”
a specific point in the recording and return to it auto¬
matically.
Pressing the PLAY button after pressing the ZERO
RETURN button activates auto play; playback auto¬
matically begins once the tape transport reaches the
“000” position. (The play indicator in the display will
flash.) The PLAY button can be pressed at any time
while the tape is being rewound or fast forwarded to
activate the function.
@ DECK TRANSPORT
© DISPLAY
a: BAR GRAPH LEVEL METERS
These six meters indicate the signal levels of the four
tape tracks and the stereo buss.
b: TAPE COUNTER
(TAPE COUNT)
This indicates the current position of the tape,
c: TAPE INDICATOR
This provides visual indication of whether the tape is
stopped or not and what direction it is moving. This
indicator lights when a cassette tape is inserted.
10