FPZ SCL K-TD MOR Series

Questions and Answers

L
Lauren LynchAug 3, 2025
What to do if my FPZ SCL K-TD MOR unit does not start?
- M
  melissa95Aug 3, 2025
  If your FPZ Blower doesn't start, there are several potential causes: * Incorrect electric wiring: Check the electric wiring against the wiring diagram located in the terminal board box. * Unsuitable power supply voltage: Ensure that the power supply voltage, measured at the motor’s terminals, is within ± 5% of the nominal voltage. * Stuck impeller: In this case, it is best to get trained personnel to repair the machine.
D
David HowardAug 7, 2025
Why does the power absorption of my FPZ Blower exceed the maximum allowed?
- R
  Robert OsbornAug 7, 2025
  If the power absorption of your FPZ Blower exceeds the maximum allowed, consider the following: * Incorrect wiring: Verify the electric wiring against the wiring diagram in the terminal board box. * Voltage drop on the power supply: Restore the power supply voltage at the terminals to within the allowed values. * Clogged intake filter: Clean or replace the cartridge. * Deposits inside the unit: Have trained personnel clean the machine internally. * Operating beyond allowed pressure/vacuum: Adjust the plant and/or the regulating valve to reduce the pressure differentials.
J
Jon NewtonAug 13, 2025
How to reduce excessive noise from my FPZ Blower?
- S
  Sean BurkeAug 13, 2025
  Excessive noise in your FPZ Blower can stem from several issues: * Damaged soundproofing fabric: Replace the soundproofing fabric. * Impeller scraping against the chassis due to: * Operating at excessive pressure/vacuum: Adjust the plant to reduce pressure differentials. * Internal deposits: Have trained personnel clean the machine internally. * Worn bearing: Replace the bearing. * Unsuitable installation position: Install the units on structures that cannot transmit or amplify the noise.
C
Christine ColeAug 17, 2025
Why is the delivery air temperature high in my FPZ Blower?
- E
  elaineclarkAug 17, 2025
  High delivery air temperature in your FPZ Blower can be due to: * Operating at excessive pressure/vacuum: Adjust the plant and/or regulating valve to reduce pressure differentials. * Clogged intake filter: Clean or replace the cartridge. * Internal deposits: Have trained personnel clean the machine internally. * Clogged intake/delivery piping: Remove the obstructions. * High intake air temperature: Use a heat exchanger to reduce the air temperature at the intake if it exceeds 40°C.
G
Gerald MurrayAug 22, 2025
What to do if the air flow rate is zero or insufficient in my FPZ SCL K-TD MOR?
- B
  bradley96Aug 22, 2025
  If your FPZ Blower has zero or insufficient airflow, check the following: * Incorrect rotation direction: Ensure the direction of rotation matches the indication on the motor’s fan cowling. * Clogged intake filter: Clean or replace the cartridge.
R
Ryan ShawAug 28, 2025
Why is my FPZ Blower experiencing abnormal vibrations?
- P
  Pamela StephensAug 28, 2025
  Abnormal vibrations in your FPZ Blower may be caused by: * Damaged impeller: Replace the impeller. * Deposits on the impeller: Get trained personnel to clean the machine internally. * Incorrect unit fixing: Fix the unit on anti-vibration supports.

Summary

General Instructions

Conditions of Use

Details on operating conditions, gas types, filters, pressure limits, and temperature ranges for safe and efficient operation.

Storage and Shipping

Guidelines for storing the unit in a dry place, handling protection plugs, and safe transport methods to prevent damage.

Installation

Instructions for installing the unit in a well-ventilated area, protecting it from direct sunlight, and mounting considerations.

Commissioning

Steps to commission the unit, including setting pressure/vacuum, checking safety valves, and measuring motor current.

Operating Adjustments

Guidance on managing driving pressure, reducing pressure losses, and using bypass valves to optimize performance.

Maintenance

Procedures for cleaning filters, periodic inspections, and bearing replacement to ensure unit longevity and performance.

Installation Sketches

Pressure Service

Diagram illustrating the installation setup for pressure service applications.

Parallel Pressure Service

Diagram showing the installation configuration for parallel pressure service.

Vacuum Service

Diagram for the installation setup in vacuum service configurations.

Parallel Vacuum Service

Diagram depicting the installation for parallel vacuum service.

List of Accessories

A list of available accessories with their respective designations for installation.

Set Up Instructions

Start-Up with 90° Manifold

Step-by-step guide for assembling and starting up the blower with a 90° manifold.

Start-Up Without 90° Manifold

Instructions for starting up the blower when using it without a 90° manifold.

Internal Cleaning Instructions

Cleaning Instructions

Detailed procedure for cleaning the internal components of the blower, referencing specific parts and figures.

Replacement Sound-Absorbing Panels

Steps for replacing the foam sound-absorbing panels in the silencer housings.

Troubleshooting

Unit Does Not Start

Identifies causes for the unit failing to start, such as wiring issues or incorrect voltage, and provides solutions.

Air Flow Rate Zero or Insufficient

Diagnoses problems like stuck impellers or clogged filters and suggests remedies for poor airflow.

Power Absorption Exceeds Maximum Allowed

Addresses issues of high power consumption due to wiring, voltage drops, or internal deposits.

Delivery Air Temperature High

Explains causes for elevated delivery air temperatures, including operating pressure and filter clogging.

Excessive Noise

Outlines reasons for increased noise levels, such as damaged soundproofing or impeller scraping.

Abnormal Vibrations

Details causes of abnormal vibrations, including impeller damage, deposits, or improper installation.