FPZ SCL K11-TD User Manual

49 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

COMPRESSORI - ASPIRATORI A CANALE LATERALE ‘SCL K-TD MOR’

ISTRUZIONI I

LATERAL CHANNEL BLOWERS - EXHAUSTERS ‘SCL K-TD MOR’

INSTRUCTIONS GB

COMPRESSEURS - ASPIRATEURS A CANAL LATERAL ‘SCL K-TD MOR’

INSTRUCTIONS F

SEITENKANALVERDICHTER - VAKUUMPUMPEN BAUREIHE ‘SCL K-TD MOR’

BETRIEBSANLEITUNG D

COMPRESORES - ASPIRADORES DE CANAL LATERAL ‘SCL K-TD MOR’

INSTRUCCIONES E

LEGGERE ATTENTAMENTE TUTTE LE ISTRUZIONI E CONSERVARLE I

PLEASE READ CAREFULLY ALL INSTRUCTIONS AND KEEP THEM FOR FUTURE REFERENCE GB

LIRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS ET LES CONSERVER F

ALLE ANLEITUNGEN SIND SORGFÄLTIG ZU LESEN UND AUFZUBEWAHREN! D

SIRVASE LEER CUIDADOSAMENTE TODAS LAS INSTRUCCIONES Y CONSERVARLAS PARA FUTURA REFERENCIA E

SN 1977-0

®

F.P.Z. effepizeta s.r.l.

Via F.lli Cervi 16/18

20049 Concorezzo - (MI) - ITALIA

Tel. +39 039 604 1820

Fax +39 039 604 1296

www.fpz.com

SCL K07 / K08 / K09 / K10 / K11

Table of Contents

Questions and Answers:

R
Ronald RichardsonAug 8, 2025
What to do if my FPZ Blower unit does not start?
- L
  Linda DuffyAug 8, 2025
  If your FPZ Blower doesn't start, there are several potential causes: * Incorrect electric wiring: Check the electric wiring against the wiring diagram located in the terminal board box. * Unsuitable power supply voltage: Ensure that the power supply voltage, measured at the motor’s terminals, is within ± 5% of the nominal voltage. * Stuck impeller: In this case, it is best to get trained personnel to repair the machine.
H
heather64Aug 12, 2025
Why does the power absorption of my FPZ SCL K11-TD exceed the maximum allowed?
- C
  Chad FergusonAug 12, 2025
  If the power absorption of your FPZ Blower exceeds the maximum allowed, consider the following: * Incorrect wiring: Verify the electric wiring against the wiring diagram in the terminal board box. * Voltage drop on the power supply: Restore the power supply voltage at the terminals to within the allowed values. * Clogged intake filter: Clean or replace the cartridge. * Deposits inside the unit: Have trained personnel clean the machine internally. * Operating beyond allowed pressure/vacuum: Adjust the plant and/or the regulating valve to reduce the pressure differentials.
V
Victor WangAug 17, 2025
How to reduce excessive noise from my FPZ SCL K11-TD Blower?
- H
  Heather EdwardsAug 17, 2025
  Excessive noise in your FPZ Blower can stem from several issues: * Damaged soundproofing fabric: Replace the soundproofing fabric. * Impeller scraping against the chassis due to: * Operating at excessive pressure/vacuum: Adjust the plant to reduce pressure differentials. * Internal deposits: Have trained personnel clean the machine internally. * Worn bearing: Replace the bearing. * Unsuitable installation position: Install the units on structures that cannot transmit or amplify the noise.

FPZ SCL K11-TD Specifications

General

Brand	FPZ
Model	SCL K11-TD
Category	Blower
Language	English

Related product manuals

FPZ SCL K10 MS-MOR

Preview: FPZ SCL K07R

FPZ SCL K03 MS-MOR

Preview: FPZ SCL K04 TD-MOR

FPZ SCL K04 TD-MOR

Preview: FPZ SCL K-TD MOR Series

FPZ SCL K-TD MOR Series

Preview: FPZ SCL K-MS MOR Series

FPZ SCL K-MS MOR Series

Preview: FPZ SCL TS Series

FPZ SCL TS Series