FRAME IT ALL RAISED GARDEN BED

To Next Page

TBD

RAISED GARDEN BED

10’ x 10’ Roundabout

Layout your Boards along the borderline and connect each

Board together by inserting the top of the stake through the

bracket loops with the stake pointing to the sky. This enables

you to freely position your border to get your desired location.

Customer Service: 1800-914-9835 |

support@frameitall.com

GARDEN BED KIT CONTAINS:

• Composite Boards 2’ x 8

• Composite Curved Boards x 27

• Cut Curved Board (Gate) x 2

• Stacking Brackets x 48

• 4-way Bracing Brackets x 24

• Stacking Stakes x 15

• Anchor Stakes x 15

• Plugs x 144

• Finishing Caps x 15

• Adapter cap x 9

ASSEMBLY INSTRUCTIONS – Level 1

STEP 1:

Assemble the Boards by sliding one end of Board into channel end

of one of the brackets. Use plugs to cover the holes on both sides to

lock the bracket in place. Connect the brackets with respect to the curvature of the board.

1. Connect 10 x 4ft Curved Boards with Stacking

brackets on both ends in alternating orientation.

2. Connect 2 x 2ft Boards with a stacking bracket on

one end and a mid-section 4-way bracket on the

other end in alternating orientation.

3. Connect 1 x 4ft Curved Board with stacking brackets

on both ends in the down position.

4. Connect 1 x 4ft Curved Board with stacking brackets

on both ends in the up position with respect to

the curve of the board.

5. Connect 1 x 4ft Curved Board with a top-section

4-way bracket on one end and a stacking bracket on

the other in the up position.

6. Connect 1 x 4ft Curved Board with a top-section

4-way bracket on one end and a stacking bracket on

the other end in alternating positions as shown to

the right

FOR INDOOR & HARD SURFACE:

If you plan to assemble raised bed on a hard surface, use

hacksaw to remove the spike of each stake. Use these cut

down stakes for the base level only of your raised garden.

Trim stake spike with

hacksawfor use indoor

or on hard surfaces

Animal Barrier & Veggie Wall

Garden

Animal Barrier Garden

Veggie Wall Garden

VEGGIE WALL COMPONENTS:

• T-Connector x 9

• L-connector x 7

• Green Nylon Netting Bundle x 4

• Cut Composite Board (Gate) x 8

• Lower Tube x 9

• Middle Tube x 9

• Upper Tube x 9

• Curved Horizontal Pole x 8

• Zip tie Pack x 4

ANIMAL BARRIER COMPONENTS:

• T-Connector x 9

• L-Connector x 7

• Black Netting Bundle x 3

• AB Part 19-C x 8

• AB Part 20 x 9

• Zip tie Pack x 3

• Gate Assembly Pieces

(see Animal Barrier assembly

section for details)

Recommended Tools:

- Hammer

- Power Drill

- Flathead Screwdriver

Need help?

Do you have a question about the FRAME IT ALL RAISED GARDEN BED and is the answer not in the manual?

Summary

Raised Garden Bed Assembly Instructions

Level 1 Assembly Overview

Step-by-step guide for assembling the first level of the raised garden bed.

Level 1 Layout and Stake Securing

Layout boards for the first level and secure stakes into the ground.

Level 2 Assembly Steps

Instructions for connecting boards and brackets for the second level.

Animal Barrier Gate Assembly

Build the Left Gate

Detailed steps for constructing the left side of the animal barrier gate.

Build the Right Gate

Detailed steps for constructing the right side of the animal barrier gate.

Attach Framework and Netting

Connecting the gate frame and applying netting to the structure.

Veggie Wall Assembly Instructions

Veggie Wall Pole Construction

Steps for assembling the vertical poles for the veggie wall.

Veggie Wall Frame Assembly

Connecting vertical poles with connectors and horizontal tubes.

Veggie Wall Netting Application

Attaching the nylon mesh netting to the veggie wall frame.

This manual describes the "Raised Garden Bed 10' x 10' Roundabout" system, a modular gardening solution designed for both vegetable walls and animal barriers. The system is manufactured by Frame It All, a company specializing in simple modular gardens.

Function Description:

The Frame It All Raised Garden Bed system allows users to construct a 10' x 10' roundabout garden bed. It is highly versatile, offering configurations for a "Veggie Wall Garden" to support climbing plants and a "Animal Barrier Garden" to protect plants from pests. The modular design enables customization and expansion, with components designed for easy assembly and disassembly. The system's primary function is to create a defined, raised planting area that can be adapted to various gardening needs, including indoor and hard surface installations with modifications.

Important Technical Specifications:

The "Raised Garden Bed Kit" includes a comprehensive set of components:

Composite Boards: 2' x 8' (8 pieces) and Curved Boards (27 pieces). These form the main structure of the raised bed.
Cut Curved Board (Gate): 2 pieces, specifically designed for gate integration.
Stacking Brackets: 48 pieces, crucial for connecting boards and creating multiple levels.
4-way Bracing Brackets: 24 pieces, providing structural stability, especially at corners and intersections.
Stacking Stakes: 15 pieces, used to secure the structure into the ground and for multi-level stacking.
Anchor Stakes: 15 pieces, for initial ground anchoring.
Plugs: 144 pieces, used to cover holes in brackets and boards, locking components in place.
Finishing Caps: 15 pieces, for a neat finish on top-level stakes.
Adapter Cap: 9 pieces, for specific connections.

For the "Veggie Wall Garden" configuration, additional components are provided:

T-Connector: 9 pieces, for connecting vertical poles and horizontal tubes.
L-connector: 7 pieces, for corner connections in the veggie wall frame.
Green Nylon Netting Bundle: 4 pieces, to create the climbing surface for plants.
Cut Composite Board (Gate): 8 pieces (note: this differs from the main kit's gate boards, suggesting specific gate functionality for the veggie wall).
Lower Tube: 9 pieces, forming the base of the vertical poles.
Middle Tube: 9 pieces, connecting lower and upper tubes.
Upper Tube: 9 pieces, forming the top section of the vertical poles.
Curved Horizontal Pole: 8 pieces, for horizontal support in the veggie wall frame.
Zip tie Pack: 4 pieces, for attaching netting.

The "Animal Barrier Components" include:

T-Connector: 9 pieces.
L-Connector: 7 pieces.
Black Netting Bundle: 3 pieces, for the animal barrier.
AB Part 19-C: 8 pieces.
AB Part 20: 9 pieces.
Zip tie Pack: 3 pieces.
Gate Assembly Pieces: Specific components for constructing the animal barrier gate.

The system is designed for a 10' x 10' roundabout shape, implying curved board segments are a key feature. The modular nature allows for multi-level construction, with stacking stakes facilitating additional tiers.

Usage Features:

Easy Assembly: The manual provides detailed, step-by-step instructions with diagrams for both the raised bed frame and the animal barrier/veggie wall. Components are designed to slide and snap together, minimizing the need for complex tools.
Customizable Shape: The initial layout process allows users to freely position boards and brackets to achieve the desired roundabout shape before securing them.
Multi-Level Capability: The system supports stacking additional levels, allowing for deeper planting areas or tiered designs.
Integrated Gate System: Both the Veggie Wall and Animal Barrier configurations include specific components and instructions for building a functional gate, providing easy access to the garden. The animal barrier gate can be integrated to swing with a board gate for a complete door.
Indoor/Hard Surface Installation: For installations on hard surfaces, the spikes of the stakes can be removed with a hacksaw, making the system adaptable for patios, decks, or indoor use.
Veggie Wall Support: The Veggie Wall setup provides a framework with netting to support climbing plants, maximizing vertical growing space.
Animal Protection: The Animal Barrier configuration creates an enclosure to protect plants from small animals, using netting and a secure gate.
Tool Recommendations: Basic household tools like a hammer, power drill, and flathead screwdriver are recommended for assembly. A hacksaw is suggested for modifying stakes for hard surface installations.

Maintenance Features:

Component Replacement: The modular design suggests that individual components could be replaced if damaged, extending the lifespan of the entire system.
Disassembly and Reconfiguration: The snap-lock plug system allows for incorrect bracket connections to be undone using a flathead screwdriver, indicating that the system can be disassembled and reconfigured if needed. This also implies ease of storage during off-seasons or relocation.
Netting Attachment: Zip ties are used to attach the netting, which allows for easy removal or re-attachment of the netting for cleaning, repair, or seasonal changes.
Durable Materials: While not explicitly stated, "Composite Boards" typically imply a durable, weather-resistant material suitable for outdoor use, reducing the need for frequent maintenance. The "Green Nylon Netting" and "Black Netting" are also likely designed for outdoor conditions.

The Frame It All Raised Garden Bed system is a comprehensive and user-friendly solution for creating a versatile and protected garden space. Its modularity, ease of assembly, and adaptability to different gardening needs make it a practical choice for various users.