Franklin Electric submonitor User Manual (English)

Other manuals for Franklin Electric submonitor

Questions and Answers:

M
Megan StewartAug 21, 2025
What to do if my Franklin Electric Protection Device shows Overload?
- R
  Robert GomezAug 21, 2025
  If your Franklin Electric Protection Device indicates an overload, there are several potential causes to investigate. First, the SF Max Amps setting may be incorrect and requires adjustment. High or low line voltage can also trigger this issue, so check the line voltage and correct it if necessary. Additionally, inspect for and resolve any ground faults. Pump or motor dragging can also cause an overload; inspect and free up any dragging components. Finally, diagnose and rectify any stall or binding issues affecting the motor or pump.
C
Colleen WilliamsAug 23, 2025
Why is my Franklin Electric Protection Device overheating?
- M
  Mark AndrewsAug 23, 2025
  Several factors can cause your Franklin Electric Protection Device to overheat. High or low line voltage can contribute, so check and stabilize the line voltage. An overloaded motor can also lead to overheating, so reduce the motor load. Excessive current unbalance, poor motor cooling, high water temperature, and excessive electrical noise from nearby VFDs can also be culprits. Balance the current, improve motor cooling, lower the water temperature, and reposition the VFD to reduce electrical noise interference.
A
Alex ClarkAug 25, 2025
What to do if my Franklin Electric submonitor indicates Underload?
- J
  Jeffrey TaylorAug 25, 2025
  If your Franklin Electric Protection Device indicates an underload condition, consider the following potential causes. The SF Max Amps setting may be incorrect and needs adjustment. Over-pumping of the well could be the issue, so inspect and adjust the well pumping operation. A clogged pump intake, closed valve, loose pump impeller, broken shaft or coupling, or a phase loss can also cause an underload. Clear any clogs, open any closed valves, tighten the impeller, repair or replace the shaft/coupling, and investigate/restore any lost phases.
J
Jennifer Martinez MDAug 27, 2025
What causes Unbalance in my Franklin Electric submonitor Protection Device?
- M
  Mr. Richard PetersAug 27, 2025
  Unbalance in your Franklin Electric Protection Device can stem from a few key issues. A phase loss could be the cause, so investigate and restore any lost phases. An unbalanced power supply can also lead to this problem; check the power supply balance and adjust as necessary. Lastly, issues with an open delta transformer can cause unbalance, so examine and repair any problems with the transformer.
J
John KelleyAug 28, 2025
What causes Overrange in Franklin Electric submonitor Protection Device?
- J
  Jeremy GutierrezAug 28, 2025
  Overrange issues in your Franklin Electric Protection Device may arise from a wrong motor voltage or SFA setting, so verify and adjust the motor settings. Excessively high line voltage or motor current can also cause overrange; reduce the line voltage or motor current accordingly.
W
Wesley DaughertyAug 29, 2025
Why does my Franklin Electric submonitor show Undervoltage?
- V
  Vanessa ReedAug 29, 2025
  Undervoltage issues with your Franklin Electric Protection Device could be due to poor connections in the motor power circuit, so inspect and rectify any poor connections. Alternatively, an unstable or weak power supply might be the cause, so stabilize the power supply to avoid undervoltage.
R
Ryan FergusonAug 31, 2025
Why does my Franklin Electric Protection Device show Overvoltage?
- U
  uromeroAug 31, 2025
  The reason your Franklin Electric Protection Device is showing overvoltage is likely due to an unstable power supply. To resolve this, ensure the power supply is stable and not fluctuating.
P
pmillerSep 1, 2025
How to fix Phase Reversal in Franklin Electric submonitor Protection Device?
- M
  Mary CollinsSep 1, 2025
  If you're experiencing phase reversal with your Franklin Electric Protection Device, it indicates an incoming power problem. Check the incoming voltage phase sequence to resolve this issue.
P
Patricia CantrellSep 3, 2025
Why does my Franklin Electric submonitor Protection Device have False Starts?
- J
  Jennifer SweeneySep 3, 2025
  False starts in your Franklin Electric Protection Device can be attributed to a few issues. Chattering contacts may be the cause, so check and replace them. Loose connections in the motor power circuit can also lead to false starts, so tighten any loose connections. Additionally, inspect and repair any arcing contacts.
N
Nicole MaynardSep 5, 2025
What to do if my Franklin Electric submonitor Protection Device shows an Overload?
- J
  Joshua LewisSep 5, 2025
  If your Franklin Electric Protection Device indicates an overload, there might be several reasons. First, the SF Max Amps setting could be incorrect, so you should adjust it. High or low line voltage can also cause this, so check and stabilize the line voltage. Inspect for any ground faults and repair them. Additionally, the pump or motor might be dragging, which needs investigation. Finally, check for a stalled motor or bound pump and clear any obstructions.

Franklin Electric submonitor Specifications

General

Frequency	50/60 Hz
Enclosure Rating	NEMA 4X
Operating Temperature	-40°C to 70°C
Storage Temperature	-40°C to 85°C
Protection Type	Phase Loss, Phase Reversal

Related product manuals

SUBMONITOR CONNECT Series

232 pages

SUBMONITOR CONNECT MT1111

232 pages

SUBMONITOR CONNECT MT2211

232 pages

Franklin Electric submonitor Installation & Operation Manual

Table of Contents

Other manuals for Franklin Electric submonitor

Questions and Answers:

Franklin Electric submonitor Specifications

Related product manuals