To Next PageTo Next PageHow to troubleshoot no power to Fri-Jado Oven controls?
If there's no power to the oven controls, here's what you can check: * See if the main breaker is open. * Replace Fuse F1 if it's burned. * Inspect the main switch; it might need replacement. * Make sure all wiring is secure.
Why does Fri-Jado STG7 P drive motor stop and start intermittently?
The drive motor might be stopping and starting again because the thermal protection has been activated. Allow the motor to cool until the temperature is below 105°C / 220°F.
Why does Fri-Jado Oven blower motor stop and start?
The blower motor might be stopping and starting again due to thermal protection activation. Allow the blower motor to cool until the temperature is below 150°C / 302°F.
Why are all heating elements out on my Fri-Jado Oven?
If all heating elements are out while the quartz lamp and blowers operate, and the oven cavity is below the set temperature, the possible causes are: * Safety thermostat malfunction: Replace the safety thermostat. * Contactor inoperative: Test the contactor and replace if inoperative. * Power board malfunction: Inspect and replace the power board if necessary. * Wiring loose: Check and secure any loose wiring.
Why isn't the drive motor running in program mode on my Fri-Jado Oven?
If the drive motor isn't running in program mode, here are a few things to check: * A malfunctioning capacitor: Replace it. * Loose wiring: Secure any loose connections. * A malfunctioning main switch: Inspect and replace if needed. * A motor malfunction: Test and replace the drive motor if necessary.
What causes the blower motor to not run on my Fri-Jado STG7 P Oven?
If the blower motor isn't running, consider these possibilities: * Capacitor malfunction: Replace the malfunctioning capacitor. * Motor inoperative: Test and replace the blower motor if it's not working. * Power board malfunction: Inspect and replace the power board if it is malfunctioning. * Wiring loose: Check and secure any loose wiring.
How to fix a Fri-Jado STG7 P Oven with no display or keypad function?
If the display and keypad aren't working, try the following: * Check if the main breaker on L2 (STG5) or L1 (STG7) is open. * Reconnect or replace the loose flat cable from the display to the electronic control. * Replace Fuse F4 (63mA) if it's burned. * Replace Fuse F1 (10A) if it's burned. * Test and replace the display or electronic control if malfunctioning. * Test and replace the keypad if malfunctioning.
What to do if Fri-Jado STG7 P temperature doesn't reach the set point?
If your oven isn't reaching the desired temperature, it could be due to: * A malfunctioning safety thermostat: Replace it. * The safety thermostat probe not being correctly positioned: Ensure it is. * An inoperative contactor: Test and replace if necessary. * A malfunctioning PT-500-sensor: Replace it. * An inoperative electronic control: Test and replace it. * Inoperative heater(s): Test and replace if necessary. * Incorrect line voltage: Check and correct it.
Why is the Fri-Jado STG7 P Oven temperature different from the setting?
If your oven temperature isn't matching the set temperature, consider these potential causes: * Incorrect line voltage: Check and correct the line voltage. * Safety thermostat malfunction: Replace the malfunctioning safety thermostat. * Safety thermostat probe position: Ensure the probe is correctly positioned. * Blower motor issues: Inspect blower motor operation and correct any turning direction issues. * Electronic control malfunction: Test and replace the electronic control if inoperative. * PT-500-sensor malfunction: Replace the malfunctioning PT-500-sensor. * Dirty fan: Clean the fanguard and fanblade(s).
Why does the main fuse or breaker blow in my Fri-Jado STG7 P Oven?
The main fuse or breaker might be blowing due to several reasons: * Incorrect wiring: Inspect and correct any wiring errors. * Shorted components: Test the heating element, drive motor, blower, or contactor switch for shorts. * Shorted wiring: Check for and fix any shorted wiring.
General| Category | Oven |
|---|---|
| Manufacturer | Fri-Jado |
| Model | STG7 P |
| Control Type | Digital |
| Number of Shelves | 7 |
| Material | Stainless Steel |
Procedures for replacing STW blower motor, thermometer, thermostat, and main switch.
Common issues and solutions for STG 5/7 rotisseries, covering power, motor, temp.
Common issues and solutions for STW 5/7 warmers, covering power, temp, controls.
Detailed diagnostics for STG 5/7 doors, elements, sensors, switches, and boards.
Detailed diagnostics for STW 5/7 doors, heating, controls, and blowers.
Circuit and wiring diagrams for the STG 5 P model.
Circuit and wiring diagrams for the STG 7 P model.
Circuit and wiring diagrams for the STW 5 model.
