What to do about whistling sound in Fri-Jado Kitchen Appliances during gas burning?
To resolve a whistling sound during gas burning in your Fri-Jado Kitchen Appliances, slightly reduce the setting screw and increase the high speed Voltage on the speed regulation board.
Why does the main fuse or breaker blow in my Fri-Jado STG5 P?
The main fuse or breaker might be blowing due to several reasons: * Incorrect wiring: Inspect and correct any wiring errors. * Shorted components: Test the heating element, drive motor, blower, or contactor switch for shorts. * Shorted wiring: Check for and fix any shorted wiring.
Why is the Fri-Jado STG5 P temperature different from the setting?
If your oven temperature isn't matching the set temperature, consider these potential causes: * Incorrect line voltage: Check and correct the line voltage. * Safety thermostat malfunction: Replace the malfunctioning safety thermostat. * Safety thermostat probe position: Ensure the probe is correctly positioned. * Blower motor issues: Inspect blower motor operation and correct any turning direction issues. * Electronic control malfunction: Test and replace the electronic control if inoperative. * PT-500-sensor malfunction: Replace the malfunctioning PT-500-sensor. * Dirty fan: Clean the fanguard and fanblade(s).
What to do if Fri-Jado STG5 P Oven temperature doesn't reach the set point?
If your oven isn't reaching the desired temperature, it could be due to: * A malfunctioning safety thermostat: Replace it. * The safety thermostat probe not being correctly positioned: Ensure it is. * An inoperative contactor: Test and replace if necessary. * A malfunctioning PT-500-sensor: Replace it. * An inoperative electronic control: Test and replace it. * Inoperative heater(s): Test and replace if necessary. * Incorrect line voltage: Check and correct it.
How to fix a Fri-Jado STG5 P Oven with no display or keypad function?
If the display and keypad aren't working, try the following: * Check if the main breaker on L2 (STG5) or L1 (STG7) is open. * Reconnect or replace the loose flat cable from the display to the electronic control. * Replace Fuse F4 (63mA) if it's burned. * Replace Fuse F1 (10A) if it's burned. * Test and replace the display or electronic control if malfunctioning. * Test and replace the keypad if malfunctioning.
Why does gas ignite then cut off quickly in my Fri-Jado Kitchen Appliances?
If the gas in the burner of your Fri-Jado Kitchen Appliances ignites but cuts off after a short time and the reset light is burning, it could be due to: * Ionization pin malfunction. Replace the ionization pin. * Adjustment of ionization pin. Adjust the ionization pin. * Loose wiring of ionization pin. Tighten any loose wiring for the ionization pin. * Gas burner safety control malfunction. Inspect and replace the gas burner safety control.
Why is the blower motor not running in my Fri-Jado Kitchen Appliances?
If the blower motor in your Fri-Jado Kitchen Appliances does not run, here are a few things to check: * A capacitor malfunction. Replace the faulty capacitor. * Loose wiring. Tighten any loose wiring. * The motor is inoperative. Replace the inoperative motor.
How do I fix no ignition in my Fri-Jado Kitchen Appliances?
If there is no ignition in your Fri-Jado Kitchen Appliances, consider the following: * Check the polarity of the plug and ensure it is correct. * Inspect and replace the gas burner safety control if it's malfunctioning. * Tighten any loose wiring.
How to troubleshoot no power to Fri-Jado Kitchen Appliances oven controls?
If your Fri-Jado Kitchen Appliances oven controls have no power, there are several potential causes: * The main breaker might be open. In this case, check and reset the main breaker. * Fuse F1 could be burned. If so, replace Fuse F1. * The main switch might have a malfunction. You should inspect and replace the main switch. * The security thermostat may have tripped, requiring a reset. * Loose wiring could also be the issue, so tighten any loose wiring.
Why does Fri-Jado Oven drive motor stop and start intermittently?
The drive motor might be stopping and starting again because the thermal protection has been activated. Allow the motor to cool until the temperature is below 105°C / 220°F.
To Next Page
General
