Fujitsu AOTG36LATL User Manual

En-6
To cancel the air conditioning, set the cursor to the zone
marked with a check, and press the [Enter button] to remove
the check mark. Unchecked zone is not air-conditioned.
NOTE
• Depending on the initial setup in the installation, there is a
case that at least one zone need to be selected.
In that case, following message is displayed on the screen,
and you need to put a check mark at least one zone.
XXXXXX
XXXXXX
One zone must be open at all times.
3
Selectroom-temperaturesensorasfollows:
Set the cursor to [Sensor] with the [Cursor button], and
press the [Enter button].
Zone
(
single
)
Zone 1
Zone 3
Zone 5
Zone 7
Zone 4
Zone 2
Zone 6
Zone 8
Zone
(
group
)
Mo 10:00
Monitor
Sensor Indoor unit
Setting:
Select desired sensor with pressing the [Cursor button
(Up/Down)].
Zone
(
single
)
Zone 1
Zone 3
Zone 5
Zone 7
Zone 4
Zone 2
Zone 6
Zone 8
Zone
(
group
)
Mo 10:00
Monitor
Cancel:
OK:
Sensor
Indoor unit
Each time you press the [Cursor button (Up/Down)],
displayed sensor switches as follows.
Non-connected sensor will be skipped.
Indoor unit Primary RC Secondary RC
Optional 1 Optional 2
To complete the setting, press the [Enter button]
.
z
1-5-2. Zone (group) setting
Enables the simultaneous setting of zone(s) and room-
temperature sensor registered into two groups that you might
have different lifestyle; “Day” and “Night”.
This setting also allows simultaneous setting to all of the con-
nected zones, as “All”.
NOTE
• When “All” is selected, the room temperature sensor speci-
edin“Sensor”of[Zone(single)setting]isapplied.
For how to group the zone(s) into “Day” or “Night”, refer to
“5-9-1. Day/Night setting”.
1
In “Monitor” screen, press the [Screen switch button
(Right)] twice.
“Zone (group)” screen opens.
Zone
(
group
)
Day
Night
All
Sensor:
Zone: Zone 1
Zone 2
Zone 3
Zone 4
Indoor
Monitor
Mo 10:00
On:
Zone
(
single
)
NOTES
• Zone(s) and room-temperature sensor grouped into “Day”
or “Night” in [Zone user setting] are displayed.
• If any names have been registered for zones and sensors
in [Zone user setting], the registered names are displayed
on this screen.
• Only zones to be air-conditioned are displayed. Undis-
played zones on this screen will not be air-conditioned.
2
Select the group to be air-conditioned with the [Cursor
button (Up/Down)], and press the [Enter button].
The group marked a check is air-conditioned.
Zone
(
group
)
Day
Night
All
Sensor:
Zone: Zone 1
Zone 2
Zone 3
Zone 4
Indoor
Monitor
Mo 10:00
Zone
(
single
)
NOTE
• The check mark currently displayed on the screen can be
unchecked only if you mark a check to the other group on
this screen, or when any setting change is done in “Zone
(single)” screen.
2. BASIC OPERATIONS
2-1. Starting the operation
PREPARATION:
Check whether the current time is displayed correctly on the
screen. When changing the time or switching the setting for
summer time (daylight saving time), follow the instructions in
“5-2. Date/Time setting”.
Menu
Monitor
Mo 10:00
O f f
9381067145_OM_EN.indd 6 14/09/2015 13:48:00

Fujitsu AOTG36LATL Specifications

General

Brand	Fujitsu
Model	AOTG36LATL
Category	Air Conditioner
Language	English