Fujitsu ASYA07LCC User Manual (English)

Other manuals for Fujitsu ASYA07LCC

Questions and Answers:

A
Ariana HallAug 20, 2025
Why my Fujitsu ASYA07LCC does not operate at all?
- L
  Lori SchneiderAug 21, 2025
  If your Fujitsu Air Conditioner isn't operating, and the Operation Lamp and Timer Lamp aren't lit, you should check a few things: * Ensure the input power voltage from the exclusive circuit AC outlet is normal. * Make sure the AC plug is securely inserted into the AC outlet and isn't loose. * Verify that any connected cables are wired correctly. * Confirm that each connector is securely inserted.
I
ingramcherylAug 22, 2025
What to do if my Fujitsu Air Conditioner shows excessive high pressure protection on cooling?
- W
  William Harvey MDAug 23, 2025
  If your Fujitsu Air Conditioner is showing an excessive high pressure protection error during cooling, check the following: * Ensure that heat radiation is not blocked at the inlet or outlet. * Verify that the outdoor fan is functioning correctly and rotating. * Check for any issues with the refrigeration cycle.
J
Justin PenningtonAug 25, 2025
What causes IPM protection in my Fujitsu Air Conditioner?
- A
  Aaron DayAug 25, 2025
  If your Fujitsu Air Conditioner is showing IPM protection, it indicates that an abnormal current value has been detected. Here's what you should check: * Ensure that heat radiation is not blocked at the inlet or outlet. * Verify that the outdoor fan is functioning correctly and rotating. * The controller PCB might be defective.
J
James DyerAug 26, 2025
What to do if my Fujitsu ASYA07LCC has indoor fan lock error?
- R
  raymondpaceAug 27, 2025
  If your Fujitsu Air Conditioner displays an indoor fan lock error, it means the indoor fan speed is 0 rpm after 56 seconds from starting or changing the fan mode. Here’s what to check: * Check the fan motor connector for looseness or defective contact. * The fan motor might be defective. * The controller PCB might be defective.
R
romerothomasAug 28, 2025
What to do if my Fujitsu ASYA07LCC Air Conditioner has indoor fan speed error?
- S
  Spencer GravesAug 28, 2025
  If your Fujitsu Air Conditioner displays an indoor fan speed error, it means the indoor fan speed is 1/3 of the target frequency after 56 seconds from starting or changing the fan mode. Here’s what to check: * Check the fan motor connector for looseness or defective contact. * The fan motor might be defective. * The controller PCB might be defective.
S
Stephanie HunterAug 29, 2025
What causes a room temperature thermistor defective in Fujitsu ASYA07LCC Air Conditioner?
- M
  Matthew JonesAug 29, 2025
  If your Fujitsu Air Conditioner shows a room temperature thermistor defect, it means the thermistor detected an abnormal temperature when the power was turned on. Check the thermistor resistance value. The controller PCB might be defective.
M
Mary ChavezAug 31, 2025
What does main relay error mean on Fujitsu ASYA07LCC?
- G
  Gregory FowlerAug 31, 2025
  If your Fujitsu Air Conditioner displays a main relay error, it means that after 2 minutes 20 seconds of stopping operation, the signal from the outdoor unit is received even though the main relay is OFF. The main relay might be defective or the Controller PCB might be defective.
L
lisa69Sep 2, 2025
Why Fujitsu ASYA07LCC Air Conditioner shows serial reverse transfer error at starting up operation?
- J
  Jill ParkSep 2, 2025
  If your Fujitsu Air Conditioner displays a serial reverse transfer error at startup, it means the indoor unit isn't receiving a signal for 10 seconds after the power relay turns on. Check the indoor/outdoor cable connection. If the wiring is normal, measure the voltage of the outdoor unit terminals and diagnose the defective location.
G
Gregory RodriguezSep 4, 2025
What does serial reverse transfer error during the operation mean for Fujitsu Air Conditioner?
- C
  Connie DeckerSep 4, 2025
  If your Fujitsu Air Conditioner displays a serial reverse transfer error during operation, it means the indoor unit isn't receiving a signal for 10 seconds. Check the indoor/outdoor cable connection. If the wiring is normal, measure the voltage of the outdoor unit terminals and diagnose the defective location.
M
Michael HartSep 5, 2025
Why Fujitsu Air Conditioner shows serial forward transfer error at starting up operation?
- R
  Rachel SmithSep 5, 2025
  If your Fujitsu Air Conditioner displays a serial forward transfer error at startup, it means the outdoor unit isn't receiving a signal for 10 seconds after the power relay turns on. Check the indoor/outdoor cable connection. If the wiring is normal, measure the voltage of the outdoor unit terminals and diagnose the defective location.