En-7
7. ENERGY SAVING OPERATIONS
7.1. Economy operation
It saves more electricity than other operation modes by changing the set
temperature to a moderate setting.
Press to activate/deactivate the Economy
operation.
[ ] indicator on the indoor unit will turn on.
Operation
mode
Room temperature
Cooling/Dry Few degrees higher than the set temperature
Heating Few degrees lower than the set temperature
NOTES:
• In the Cooling, Heating, or Dry mode, the maximum output of this
operation is approximately 70 % of usual operation.
• This operation cannot be performed during the temperature
monitoring by the Auto mode.
7.2. Fan control for energy saving
In the Cooling operation, when the room
temperature reaches the set temperature, the
indoor unit fan rotates intermittently to save
power. (This function is activated at the time of
purchase.)
To change the setting, use the following
steps;
1. Press
until only the clock is displayed on the remote
controller display.
2. Press down
for more than 5 seconds.
The current Fan Control status ( ) is displayed.
3. Press
to switch between activated ( ) or
deactivated (
).
4. Press
to send the setting to the indoor unit.
The display will return to the original screen.
NOTES: If you do not press any buttons for 30 seconds after
is
displayed,
step 2.
8. OTHER OPERATIONS
8.1. Powerful operation
In the Powerful operation, the air conditioner will operate at maximum
NOTES: In multi connection, this function cannot be used.
Press to activate/deactivate the Powerful operation.
When activated, the indoor unit will emit 2 short beeps.
When deactivated, the indoor unit will emit 1 short beep.
situations:
• The Powerful operation runs for a certain amount of time and the
room temperature reaches the set temperature in the Cooling, Dry,
or Heating mode.
• 20 minutes after the Powerful operation has started.
NOTES:
•
• The Powerful operation cannot be performed simultaneously with
Economy operation.
• The Powerful operation overrides the following operations. If the
following operation is set, they will start after the Powerful operation
- Outdoor Unit Low Noise operation
• If the wired remote controller (optional) is connected, this function is
restricted.
■
Examples of Weekly timer
Example 1
7:00 9:00 11:00 17:00 23:00
Monday
to
Friday
Program
1
Program
2
Program
3
Program
4
On On
26 °C 28 °C
Wake up Leave for
work
Come back
home
Go to
sleep
Saturday (No timer settings)
Sunday Program
1
Program
2
Program
3
Program
4
(On) (On) (On) (On)
Example 2: You can specify temperature settings using the On timer in
the Weekly timer.
7:00 9:00 17:00 23:00
Program 1 Program 2 Program 3 Program 4
On On On On
28 °C 26 °C 27 °C 28 °C
6.2. On timer or O timer
1.
2. Press
Pressing the button: The time will change by +5/-5 minutes.
Pressing down the button: The time will change by +10/-10 minutes.
•
while is
shown on the remote controller display.
The indicator will disappear.
6.3. Program timer
1.
2.
The order of the timer operation is displayed as follows:
Timer Indicator on the remote controller display
NOTES: You can set the Program timer only within a span of 24 hours.
6.4. Sleep timer
1.
2. Press
to set the time until the operation
stops.
Each time you press the button, the time changes as follows:
00M
00M
00M
00M
00M
00M
30M
hours
(30 min.)
• To deactivate the Sleep timer, press while is shown
on the remote controller display.
The indicator will disappear.
During the Sleep timer operation, the setting temperature changes as
In Heating mode
Set
temperature
Set time
1 hour
Set time
1 hour
1.5 hour
30 min.
1 °C 2 °C 3 °C 4 °C
2 °C
1 °C
In Cooling or Dry mode
9387602142-02_OM.indb 7 01/12/2022 13:04:00
To Next Page
Loading...
Need help?
General
