EasyManua.ls Logo

Fujitsu ESPRIMO D538 - User Manual

Fujitsu ESPRIMO D538
39 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
System
Operating Manual
FUJITSU Desktop
ESPRIMO D53x / D73x

Table of Contents

Questions and Answers

  • H
    Heidi GarciaAug 7, 2025
    What to do if the power-on indicator is unlit on my Fujitsu Desktop?
    • D
      Deborah AndrewsAug 8, 2025
      If the power-on indicator is unlit after switching on your Fujitsu Desktop, the mains voltage supply could be faulty. Check whether the power cable is properly plugged into the device and a grounded mains outlet. Another cause could be an overloaded internal power supply. To resolve this, pull the power plug out of the mains outlet, wait approximately 3 minutes, plug it back into a grounded outlet, and switch the device on again.
  • B
    brittany59Aug 12, 2025
    What to do if my Fujitsu Desktop can't be switched off with the On/Off switch?
    • W
      williamsjonathanAug 12, 2025
      If your Fujitsu Desktop cannot be switched off with the On/Off switch, it may be due to a system crash. Press the On/Off switch for at least 4 seconds until the device switches off. Warning: this could lead to data loss because the operating system will not shut down properly, and error messages may appear the next time the system is booted.
  • J
    julialevineAug 17, 2025
    What to do if no mouse pointer is displayed on Fujitsu ESPRIMO D538 screen?
    • D
      Dr. Gregory Wagner Jr.Aug 17, 2025
      If no mouse pointer is displayed on your Fujitsu Desktop screen, the mouse may not be correctly connected. Shut down your operating system properly (e.g., using Ctrl + Alt + Del), switch the device off, and check that the mouse cable is properly connected to the system unit. If you're using an adapter or extension lead, check those connections. Ensure only one mouse is connected. Then, switch the device back on. Also, check in the BIOS Setup whether the used USB ports are enabled.
  • K
    kevin70Aug 22, 2025
    Why is my Fujitsu ESPRIMO D538 monitor blank?
    • B
      Brandon DrakeAug 23, 2025
      Your Fujitsu Desktop monitor might be blank because it is switched off, so turn it on. Power saving may be activated, in that case, press any key or deactivate the screen saver and enter your password if needed. The brightness control could be set too low, so adjust it. Also, check if the power and monitor cables are properly connected to both the device and the power outlet. If the monitor setting is incorrect, restart the system, press F8 while booting, start in Safe Mode, and set up the monitor as described in your operating system and monitor documentation.
  • A
    aguirregeraldAug 27, 2025
    How to fix incorrect time and date on Fujitsu Desktop?
    • L
      leahmcdanielAug 27, 2025
      If the time and date are incorrect on your Fujitsu Desktop, set the correct time and date within the operating system or in the BIOS Setup. If the time and date are repeatedly wrong when you switch your device off and then on, change the lithium battery.
  • S
    Sarah MitchellSep 1, 2025
    What to do if my Fujitsu ESPRIMO D538 Desktop SmartCard reader is not recognized?
    • A
      Alejandro MillsSep 1, 2025
      If your Fujitsu Desktop SmartCard reader is not recognized, check that you have inserted your SmartCard correctly, with the chip facing upwards. Also, verify that the SmartCard complies with the ISO standard 7816-1, -2, -3, and -4, and is supported by the reader.

Summary

Important notes

Safety information

Essential safety precautions for operating the device.

Device overview

Getting started

Steps for initial setup

Key steps required for the first-time operation of the device.

Setting up the device

Connecting the device to the mains supply

Connecting external devices

Ports on the device

Connecting a monitor

Switching on for the first time: installing the software

Switch on the monitor and the machine

Procedure for powering on the system and monitor for initial setup.

Installing the software

Steps for installing the operating system and initial software.

Operation

Procedure in an emergency

Steps to follow for forced shutdown in emergencies.

Settings in BIOS Setup

Property and data protection

Anti-theft protection and lead-sealing

Delete data

Software installation and restore

Installing new software

Download current drivers;software

Instructions for obtaining the latest drivers and software.

Problem solutions and tips

Help if problems occur

Information on seeking assistance and contacting support.

Troubleshooting

Common issues and their solutions for device malfunctions.

The device cannot be switched off with the On;Off switch

Monitor remains blank

Solutions for display issues where the monitor shows no image.

No mouse pointer displayed on the screen

Time and;or date is not correct

SmartCard reader is not recognised

System expansions and repairs

Fujitsu ESPRIMO D538 Specifications

General IconGeneral
BrandFujitsu
ModelESPRIMO D538
CategoryDesktop
LanguageEnglish

Related product manuals