EasyManua.ls Logo

Fujitsu ESPRIMO D738 - User Manual

Fujitsu ESPRIMO D738
39 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
System
Operating Manual
FUJITSU Desktop
ESPRIMO D53x / D73x

Table of Contents

Questions and Answers

  • N
    Nancy DominguezAug 7, 2025
    What to do if the power-on indicator is unlit on my Fujitsu Desktop?
    • D
      David MartinAug 7, 2025
      If the power-on indicator is unlit after switching on your Fujitsu Desktop, the mains voltage supply could be faulty. Check whether the power cable is properly plugged into the device and a grounded mains outlet. Another cause could be an overloaded internal power supply. To resolve this, pull the power plug out of the mains outlet, wait approximately 3 minutes, plug it back into a grounded outlet, and switch the device on again.
  • S
    Stacey MartinezAug 12, 2025
    What to do if my Fujitsu ESPRIMO D738 Desktop can't be switched off with the On/Off switch?
    • C
      Candice EdwardsAug 12, 2025
      If your Fujitsu Desktop cannot be switched off with the On/Off switch, it may be due to a system crash. Press the On/Off switch for at least 4 seconds until the device switches off. Warning: this could lead to data loss because the operating system will not shut down properly, and error messages may appear the next time the system is booted.
  • M
    Megan ArmstrongAug 17, 2025
    What to do if no mouse pointer is displayed on Fujitsu ESPRIMO D738 screen?
    • C
      Chase LiuAug 17, 2025
      If no mouse pointer is displayed on your Fujitsu Desktop screen, the mouse may not be correctly connected. Shut down your operating system properly (e.g., using Ctrl + Alt + Del), switch the device off, and check that the mouse cable is properly connected to the system unit. If you're using an adapter or extension lead, check those connections. Ensure only one mouse is connected. Then, switch the device back on. Also, check in the BIOS Setup whether the used USB ports are enabled.
  • S
    Sandra MasonAug 22, 2025
    Why is my Fujitsu ESPRIMO D738 Desktop monitor blank?
    • L
      lisa94Aug 22, 2025
      Your Fujitsu Desktop monitor might be blank because it is switched off, so turn it on. Power saving may be activated, in that case, press any key or deactivate the screen saver and enter your password if needed. The brightness control could be set too low, so adjust it. Also, check if the power and monitor cables are properly connected to both the device and the power outlet. If the monitor setting is incorrect, restart the system, press F8 while booting, start in Safe Mode, and set up the monitor as described in your operating system and monitor documentation.
  • V
    Veronica HuntAug 27, 2025
    How to fix incorrect time and date on Fujitsu ESPRIMO D738?
    • F
      faulknergeraldAug 27, 2025
      If the time and date are incorrect on your Fujitsu Desktop, set the correct time and date within the operating system or in the BIOS Setup. If the time and date are repeatedly wrong when you switch your device off and then on, change the lithium battery.
  • J
    jjohnsonSep 1, 2025
    What to do if my Fujitsu ESPRIMO D738 SmartCard reader is not recognized?
    • G
      Greg CaseSep 1, 2025
      If your Fujitsu Desktop SmartCard reader is not recognized, check that you have inserted your SmartCard correctly, with the chip facing upwards. Also, verify that the SmartCard complies with the ISO standard 7816-1, -2, -3, and -4, and is supported by the reader.

Summary

Important Notes

Safety Information Guidelines

Provides crucial safety guidelines and warnings for operating the device and preventing hazards.

Getting Started

Unpacking and Initial Setup

Guide on unpacking the device, checking contents, and initial setup steps.

Device Setup and Positioning

Power Connection Guide

Connecting External Devices

Device Ports Identification

Connecting Essential Peripherals

Instructions for connecting monitors, mice, and keyboards to the computer.

Connecting via Serial and USB Ports

Details on connecting devices via serial and USB ports, including driver information.

First-Time Setup and Software Installation

Initial Device Power On

Steps for switching on the monitor and the machine for the initial setup.

System Software Installation Process

Guidance on following on-screen instructions for installing system software and drivers.

Operation

Device Power Management

BIOS Setup and Configuration

Security Features Overview

Details on anti-theft protection, mechanical casing locks, and BIOS security functions.

Data Deletion Procedures

Fujitsu ESPRIMO D738 Specifications

General IconGeneral
GraphicsIntel UHD Graphics 630
Operating SystemWindows 10 Pro
Form FactorSmall Form Factor
ChipsetIntel Q370
Max RAM64 GB
AudioRealtek ALC671
Power Supply280 W
Storage (Alternative)500 GB HDD
Optical DriveDVD Super Multi drive
NetworkingGigabit Ethernet, Wi-Fi 802.11ac

Related product manuals