Fujitsu PRIMERGY CX2560 M4 - Page 9

CX2550/60/70 M4 Upgrade and Maintenance Manual
Contents
5.2.2 Verifying system information backup / restore . . . . . . . . . . 83
5.2.3 Updating expansion card firmware . . . . . . . . . . . . . . . 83
5.2.4 Enabling Option ROM scan . . . . . . . . . . . . . . . . . . . 85
5.2.5 Resetting the boot retry counter . . . . . . . . . . . . . . . . . 86
5.2.5.1 Viewing the boot retry counter . . . . . . . . . . . . . . . . 86
5.2.5.2 Resetting the boot retry counter . . . . . . . . . . . . . . . 86
5.2.6 Enabling SVOM boot watchdog functionality . . . . . . . . . . 88
5.2.7 Enabling replaced components in the BIOS . . . . . . . . . . . 89
5.2.8 Reconfiguring the backup software solution . . . . . . . . . . . 90
5.2.9 Verifying the memory mode . . . . . . . . . . . . . . . . . . . 90
5.2.10 Verifying the system time settings . . . . . . . . . . . . . . . . 92
5.2.11 Viewing and clearing the System Event Log (SEL) . . . . . . . 93
5.2.11.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . 93
5.2.11.2 Clearing the SEL . . . . . . . . . . . . . . . . . . . . . . . 94
5.2.12 Updating the NIC configuration file in a Linux and VMware
environment . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
5.2.13 Resuming BitLocker functionality . . . . . . . . . . . . . . . . 96
5.2.14 Performing a RAID array rebuild . . . . . . . . . . . . . . . . . 97
5.2.15 Looking up changed MAC/WWN addresses . . . . . . . . . . 97
5.2.15.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . 98
5.2.15.2 Looking up WWN addresses . . . . . . . . . . . . . . . . . 98
5.2.16 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . . 99
5.2.17 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . 100
5.2.17.1 After replacing/upgrading LAN controllers . . . . . . . . . . 100
5.2.17.2 After replacing a system board . . . . . . . . . . . . . . . . 100
5.2.18 Switching off the ID indicator . . . . . . . . . . . . . . . . . . 101
5.2.19 Performing a fan test . . . . . . . . . . . . . . . . . . . . . . 101
5.2.20 Resetting the error status after replacing CPUs . . . . . . . . . 103
5.2.20.1 CPUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5.2.21 Updating ServerView RAID Manager . . . . . . . . . . . . . . 104
6 Expansion cards and OCP mezzanine cards . . . . . . . . . 105
6.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 106
6.1.1 CX2550 M4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
6.1.2 CX2560 M4 / CX2570 M4 . . . . . . . . . . . . . . . . . . . . 110
6.2 Expansion cards in the riser module . . . . . . . . . . . . . 118
6.2.1 Installing expansion cards . . . . . . . . . . . . . . . . . . . . 119
6.2.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 119
6.2.1.2 Mounting a controller to the riser module . . . . . . . . . . 120
6.2.1.3 Connecting cables to the expansion card . . . . . . . . . . 121