13 EN
Time Search
This feature allows you to go to a specific point on a tape by
entering the exact amount of time you wish to skip in order to
reach the point.
If a tape includes both programmes recorded in the PAL
system and ones recorded in the NTSC system, this function
may not be operated correctly.
• Use the remote control for this procedure.
1) Press
VCR, then SEARCH twice.
2) Press
K or L repeatedly until the desired time appears.
3) Press
s or B to start Time Search.
•The unit begins rewinding or fast forwarding to the
specified point. When 0:00 is reached, the unit will start
playback automatically.
Note: • Time Search can be set up to 9 hours 59 minutes
(9:59).
• This function will not operate in the Recording mode.
• Operations must be followed up within 30 seconds
from steps 2) to 3), otherwise the Time Search mode
will be cancelled.
• To exit the Time Search mode, press SETUP in step 2)
or press STOP C after step 3).
Recording
Viewing and Recording the Same Programme
1) Insert a cassette tape with its erase-prevention tab in place.
(If necessary, rewind or fast forward the tape to the point
at which you want to begin recording.) Press
VCR.
2) Press
the Number buttons or CHANNEL (K/L) to select
the channel to be recorded.
3) Press
SPEED/SYSTEM to select the tape speed (SP/LP).
4) Press
REC/OTR to begin recording.
•The REC/OTR indicator on the front panel comes on.
5) Press
STOP C when recording is completed.
Two Different Tape Speeds
Before recording, select the tape speed: SP mode (Standard
Play) or LP mode (Long Play). The table below shows the
maximum recording/playback time using E-60, E-120, E-180
or E-240 tapes in each mode.
Skipping Unwanted Programme Material During
Recording
1) Press PAUSE F when you want to temporarily halt
recording.
You can check the remaining pause time with
C
marks on
the TV screen. Each
C
mark represents 1 minute. After 5
minutes, the unit will automatically switch to the Stop
mode to prevent tape damage.
2) Press
PAUSE F or REC/OTR to resume recording.
Recording One Programme While Viewing Another
You can record one programme while viewing another. To
start recording, follow steps 1) to 4) in the “Viewing and
Recording the Same Programme”. Then, set the TV to the
channel you want to watch.
To Monitor the Progress of Your Recording
Select the video channel on the TV.
Assemble Function
You can record in continuation from previous programme on
a pre-recorded tape.
1) Insert a pre-recorded tape. Press
PLAY B to start playback.
2) Press PAUSE F at the desired point on the tape.
3) Press REC/OTR. The unit will be in the Recording Pause
mode.
4) Press CHANNEL (K/L) to select the channel to be
recorded.
5) Press REC/OTR or PAUSE F. The recording will begin.
6) Press STOP C when recording is completed.
Note: • DVD to VCR dubbing via the DVD/VCR deck of
this unit is not supported.
OTR (One Touch Recording)
This function enables you to set the duration of a recording
simply by pressing REC/OTR.
1) Follow steps
1) to 3) in “Viewing and Recording the Same
Programme”.
2) Press
REC/OTR repeatedly until the desired recording
length appears in the upper left corner of the TV screen.
Recording stops when 0:00 is reached.
• To check time remaining during an OTR, press
DISPLAY.
• To change the recording length during an OTR, press
REC/OTR repeatedly until the desired length appears.
• To stop an OTR before recording is finished, press
STOP C.
• To cancel the OTR but continue recording, press
REC/OTR
repeatedly until “I” appears without the recording length.
Timer Recording
You may programme the unit to start and end a recording
while you are away. You can set 8 programmes to record on
specific days, daily or weekly within a 1-year period.
• Use the remote control for this procedure.
• Insert a cassette tape with its erase-prevention tab in place.
(If necessary, rewind or fast forward the tape to the point at
which you want to begin recording.)
1) Press
VCR, then SETUP.
2) Press
K or L to select “TIMER”, then press B.
Note: • If you have not set the clock yet, “CLOCK” setting
menu appears. If so, follow the steps outlined in the
“Setting the Clock”. (Refer to page 9.) Then, set the
timer.
•When you press
B after pressing K or L during steps 3) to
7), the input mode will move to the next item.
• If you do not press
B within 5 seconds of setting an item,
the input mode will move to the next item.
•Press
s to go back to the previous item from the current
setting during steps
4) to 8). If s is pressed when the
TIMER NUMBER is flashing, the entire programme
contents will be erased.
3) Programme number flashes. Press
K or L repeatedly until
the desired programme number appears. Then, press B.
4) Select once, daily, everyday or weekly recording.
For once-only recording: Press K or L repeatedly until
the relevant month appears, and then press K or L
repeatedly until your desired day appears.
Tape Type Recording/Playback Time
Tape Speed SP Mode LP Mode
E-60 1 hour 2 hours
E-120 2 hours 4 hours
E-180 3 hours 6 hours
E-240 4 hours 8 hours
I I [0:30] I[1:00]... I[7:30] I[8:00]
(Normal (OTR:
recording) 30 minutes)
E8GA5BD(EN).fm Page 13 Tuesday, April 17, 2007 11:56 AM
To Next Page
Loading...
