FUTABA 12Z Series - Page 108

108
<Functions of Model Menu (Helicopter Functions)>
Normal Curve Idle-up 1 Curve Idle-up 2 Curve Hold Curve
Ɣ3LWFK&XUYH([DPSOH
ŏ*URXS6LJOHLWHP:KHQ\RXDOVRZDQWWRLQSXW
WKHVDPHVHWWLQJFRQWHQWVDWRWKHUFRQGLWLRQV
SHUIRUPVHWWLQJLQWKHJURXSPRGHLQLWLDOVHWWLQJ
,QWKLVFDVHWKHVDPHFRQWHQWVDUHLQSXWWRWKH
RWKHUFRQGLWLRQVVHWLQWKHJURXSPRGH:KHQ\RX
ZDQWWRVHWHDFKFRQGLWLRQLQGHSHQGHQWO\VHOHFW
WKHVLQJOHPRGH2WKHUFRQGLWLRQVFDQEHVHW
independently.
Setting method
ŏ7KHVHUYRRSHUDWLRQVSHHGFDQEHVHW
ŏ:KHQLQFUHDVLQJWKHQXPEHURISRLQWVPRYHWKH
FXUVRUWR326,7,21LWHPDQGURWDWHWKHGDWDLQSXW
GDLDOWRPRYHWRWKHSRLQWZKHUH\RXZDQWWR
enter a point and push the enter button. The point
is created.
The screens shown below are curves created by
entering the pitch rate at low, center, and high side
3 points or 5 points at each condition. They were
created by reducing the number of points to the
3 points of low side, center, and high side. When
DFWXDOO\FUHDWLQJDFXUYHLQSXWWKHUDWHVSHFL¿HGDW
the fuselage (or the reference value).
*For a description of the curve setting method, see the
description at the back of this manual.
Curve setting examples
(Continued on next page)
Pitch Trim (Hovering pitch, high pitch, low pitch)
The hovering pitch, low pitch, and high pitch trim setup screen can be called from the PIT Curve setup
screen.
ŏ+RYHULQJSLWFK
WULPVHWWLQJ
ŏ/RZ+LJKSLWFK
WULP
ﶴﷂﶬﵺ﷎ﶪﶰﶨ﷊
ﴶﴸﴸﳜ
ﶺﶶ﷌﷊ﶼ﷤
ﶸﶶﶰﶺ﷒ﶼ
ﴶﴸﳰﴶﴸﳰﴸﴸ
Ｂ８Ｄ
﷒﷎ﶬ
﹪﹤﹔󾷉﹢ﹰ﹚ﹼﹲ
ﷆﶰﶶﶪﶴ
﷎ﶬﶰﶼ
Ｆ０４
８＊＜＜
ﶰ﷒ﶬ﷊
ﻚﻤ
ｆﻪ
ﶈﵺﶄ﷦ﶊﶆ
ﹲﹰﹴﹲ󾷉﹢ﹰ﹚ﹼﹲ
Ｂ８Ｄ
﷒﷎ﶬ
ﷆﶰﶶﶪﶴ
﷎ﶬﶰﶼ
Ｆ０４
８＊＜＜
ﶰ﷒ﶬ﷊
ﻚﻤ
ｆﻪ
ﶈﵺﶄ﷦ﶊﶆ
ﶴﷂﶬﵺ﷎ﶪﶰﶨ﷊
ﴶﴸﴸﳜ
ﶺﶶ﷌﷊ﶼ﷤
ﶸﶶﶰﶺ﷒ﶼ
ﴶﴸﳰﴶﴸﳰﴸﴸ
Ｂ８Ｄ
﷒﷎ﶬ
ﹲ﹤﹖ﹸ﹞
ﷆﶰﶶﶪﶴ
﷎ﶬﶰﶼ
Ｆ０４
Ｎ，０：
８＊＜＜ ｄｆｆﻪ
ﶰ﷒ﶬ﷊
ﻚﻤ
｀ｆﻪ
ﶈﵺﶄ﷦ﶊﶆ
ﶺﶶ﷌﷊
ﶰ﷒ﶸﷆ﷊