FUTABA 12Z Series - Model Menu Functions List

78
<Model Menu (Airplane/Glider Functions)>
PUSH
[Cursor Lever]
Ɣ0RYHPHQWRQWKH
VFUHHQGLUHFWLRQV
Ɣ3XVKWKHOHYHUWRFDOO
QH[WSDJH
[Data Input Dial]
[Enter Button]
[Return Key]
Ɣ7RKRPH
VFUHHQ
Ɣ7RSUHFHGLQJ
VFUHHQ
MODEL MENU (AIRPLANE/GLIDER FUNCTIONS)
The dedicated mixes, etc. usable when airplane,
glider, or EP glider model type is selected are
displayed in this Model Menu functions section.
First use the Model Type function of the Linkage
Menu to preset the model type, wing type, and tail
type matched to the fuselage used. Later setting
resets the data set by mixing function, etc.
These dedicated mixes can be set for each
flight condition, as required. When you want to
use the system by switching the settings for each
condition by switch or stick position, use the
&RQGLWLRQ6HOHFWIXQFWLRQWRDGGÀLJKWFRQGLWLRQV
(Up to 8 conditions can be used)
Note: The T12Z is designed so that the airplane and
glider (including EP glider) model types can handle
aircraft of the same wing type.
The functions common to airplanes and gliders,
except some dedicated functions, are summarized
without regard to the model type.
The setting items are different, depending on the
number of servos, etc. according to the wing type
used. The setup screens in the instruction manual
are typical examples.
Model Menu functions list
AIL DIFFERENT.
This function adjusts the left and right ailerons.
5ROOD[LVFRUUHFWLRQDQG¿QHWXQLQJZLWKD95DUH
also possible. This is convenient when making
VHWWLQJVGXULQJÀLJKW
[Airplane/glider, 2 ailerons or more]
FLAP SETTING
7KHÀDSVFDQEHDGMXVWHGLQGHSHQGHQWO\)RUD
ÀDSVPRGHOWKHFDPEHUÀDSVFDQEHPL[HGZLWK
WKHEUDNHÀDSV>$LUSODQHJOLGHUÀDSVRUPRUH@
AIL to CAMBERFLP
This mix operates the camber flaps in
the aileron mode. It improves the operation
characteristic of the roll axis. [Airplane/glider, 2
DLOHURQVÀDSVRUPRUH@
AIL to BRAKEFLP
7KLVPL[RSHUDWHVWKHEUDNHÀDSVLQWKHDLOHURQ
mode. It improves the operation characteristic of
WKHUROOD[LV>$LUSODQHJOLGHUÀDSVRUPRUH@
AIL to RUD
This mix is used when you want to operate the
rudder at aileron operation. Banking at a shallow
bank angle is possible. [Airplane/glider, general]
AIRBRAKE to ELE
This mix is used to correct operation of the
airbrakes (spoilers) when landing. [Airplane/
glider, general]
ﶺﶶ﷌﷊ﶼﵺﶺ﷊ﶸﶪ
ＲＨ０ﻚﻨＬﻜ０ﻦ
．Ｊ０（６ﻚ：６８Ｂ，６０
ＲＢ＜ﻚＬＢＨＨＪ０Ｊ：，ﻞ
ＲＢ＜ﻲＮＲ：ＰＪ０Ｈ＜４
Ｎ６８ＬＢ，ﻞ．Ｊ＜ＪＮ，
４０６Ｆﻞﻚ：Ｂ＄Ｊ．
Ｈ＜Ｒ４ﻚ．Ｊ，，Ｂ８Ｆ
ＲＢ０Ｐ０Ｒ＞ＪﻲＪ＜Ｊ
ﴶﴸﴸﳜ
ﶺﶶ﷌﷊ﶼ﷤
﷎ﶶﶸ﷌ﷂﶬ﷤
ﴶﴸﳰﴶﴸﳰﴸﴸ
ＲＢ＜ﻲ０＊Ｌ
ＲＢ＜ﻲＰ０Ｒ＞ＪＨ＜４
ﶺﶶ﷌﷊ﶼﵺﶺ﷊ﶸﶪ
０＊ＬﻲＪ＜Ｊ
ＮＲ：ＰＪ０Ｈ＜４ﻲＪ＜Ｊ
ＲＢ０Ｐ０Ｒ＞Ｊ
：＊＜，ＢﻚＪ８ＦＢ８Ｊ
．８Ｒ４ﻚ０６＜＜
Ｈ＊Ｊ＜ﻚ：Ｂ＄，＊０Ｊ
ﴶﴸﴸﳜ
ﶺﶶ﷌﷊ﶼ﷤
﷎ﶶﶸ﷌ﷂﶬ﷤
ﴶﴸﳰﴶﴸﳰﴸﴸ
（ﻠ，ＲＢ＜
Ｆ＂０６
０＊ＬﻲＲＢ＜
(Model Menu screen example)
*The Model Menu screen depends on the model type.
This screen is for model type 4AIL+4FLP.
ŏ6HOHFWWKHPRGHOPHQXLFRQDWWKHKRPH
screen and call the model menu shown
below by pushing the enter button.
ŏ8VHWKHFXUVRUOHYHUWRVHOHFWWKHIXQFWLRQ
you want to set and call the setup screen by
pushing the enter button..