FUTABA 12Z Series - Page 28

28
<Functions of System Menu>
PUSH
[Cursor Lever]
Ɣ0RYHPHQWRQWKH
VFUHHQGLUHFWLRQV
Ɣ3XVKWKHOHYHUWRFDOO
QH[WSDJH
[Data Input Dial]
[Enter Button]
[Return Key]
Ɣ7RKRPH
VFUHHQ
Ɣ7RSUHFHGLQJ
VFUHHQ
When using at the teacher side
6HOHFWWKHPRGH
*When changing the mode, use the cursor lever to move
to the item you want to change and change the mode by
turning the data input dial to the left or right. The display
blinks. Press the enter button to change the mode.
 7($&+(5678'6HOHFW>7($&+@
 $&7,1+(QDEOHRSHUDWLRQE\FKDQJLQJWR
>2))@RU>21@
 &+$11(/:KHQWKHVWXGHQWXVHVWKH
7=LQFOXGLQJWKH70=RU);VHOHFW
>&+@2WKHUZLVHVHOHFW>&+@
6HOHFWWKHWUDLQHUVZLWFK
*When setting or changing the switch, use the cursor lever to
move to the "SWITCH" item, call the switch setup screen
by pushing the enter button and set the desired switch and
ON/OFF direction.
 6HH6ZLWFKVHOHFWLRQPHWKRGDWWKHHQGRI
WKLVPDQXDOIRUVHOHFWLRQPHWKRGGHWDLOV
*The switch mode can also be selected when setting the
TRAINER
Trainer system starting and setting
The Trainer function makes it possible for the
instructor to choose which functions and channels
are to be used for instruction, making it possible to
match the training ability to the student's skill level.
Two transmitters must be connected by an optional
Trainer Cord, and the Instructors’ transmitter
should be programmed for trainer operation, as
described below.
When the Instructor activates the trainer switch,
the student has control of the aircraft (if MIX or
FUNC mode is turned on, the Instructor can make
corrections while the student has control). When
the switch is released the Instructor regains control.
This is very useful if the student gets the aircraft
into an undesirable situation.
NOTE: This trainer system can be used in the
following manner;
1. With the T12Z transmitter and a conventional
transmitter, if the channel order is different. It
is necessary to match the channel order in
the Function setting screen when connecting
it with other than a T12Z.
2. When the T12Z is used as the Teacher, set the
modulation mode of the student’s transmitter
to PPM. If being used as the student, set
the T12Z to the modulation mode specified
by the Instructors’ transmitter. When the
Instructors’ transmitter is a T14MZ, 12Z, T9Z,
T9C or T7C transmitter, it should be switched
to PPM mode.
3. Be sure that all channels work correctly in
ERWKWUDQVPLWWHUVEHIRUHÁ\LQJ
ŏ6HOHFW>75$,1(5@DWWKHV\VWHPPHQXDQGFDOOWKH
VHWXSVFUHHQVKRZQEHORZE\SXVKLQJWKHHQWHU
EXWWRQ
(The display screen is an example. The screen depends on the model type.)
ON position on the switch setup screen. When [NORM] is
selected, normal ON/OFF operation is performed. When
[ALT] is selected, the trainer function is alternately turned
on and off each time the switch is operated. This allows
alternate ON/OFF switching even when a momentary switch
(SH) is used.
6HOHFWWKHRSHUDWLQJPRGHIRUHDFKFKDQQHO
*Use the cursor lever to move the cursor to the "MODE" item
of the channel you want to change and change the mode by
turning the data input dial to the left or right. The display
blinks. Press the enter button to change the mode.
 12507KHPRGHOLVFRQWUROOHGE\VLJQDOV
IURPWKHVWXGHQWWUDQVPLWWHU
 0,;PRGH7KHPRGHOLVFRQWUROOHGE\
VLJQDOVWUDQVPLWWHGIURPWKHWHDFKHUDQG
ﶬﶰ﷒ﷂﶸ﷊ﶰ
６ＨＨ
６ＨＨ
﷎ﷄﵺ﷈ﶪﶸ﷎ﶬﷂﶶﶸ
ﴶﴸﴸﳜ
﷤ ﷊ﶼ﷊ﶨ﷒ﶬﶶﶰ
﷢ ﶰﶪ﷌﷌﷊ﶰ
﷠ ﶬﷄﶰﶶﶬﶬﶼ﷊
﷞ ﷒ﷂﶼ﷊ﶰﶶﶸ
ﶺﶶ﷌﷊ ﶮﶦ ﶰ﷒ﶬ﷊
６ＨＨ
６ＨＨ
８＊＜＜
８＊＜＜
８＊＜＜
８＊＜＜
ﶺﶶ﷌﷊ﶼ﷤
﷎ﶶﶸ﷌ﷂﶬ﷤
ﴶﴸﳰﴶﴸﳰﴸﴸ
ﶬﶰ﷒ﷂﶸ﷊ﶰ
６ＨＨ
６ＨＨ
﷎ﷄﵺ﷈ﶪﶸ﷎ﶬﷂﶶﶸ
ﴶﴸﴸﳜ
﷤ ﷊ﶼ﷊ﶨ﷒ﶬﶶﶰ
﷢ ﶰﶪ﷌﷌﷊ﶰ
﷠ ﶬﷄﶰﶶﶬﶬﶼ﷊
﷞ ﷒ﷂﶼ﷊ﶰﶶﶸ
ﶺﶶ﷌﷊ ﶮﶦ ﶰ﷒ﶬ﷊
６ＨＨ
６ＨＨ
８＊＜＜
８＊＜＜
８＊＜＜
８＊＜＜
ﶺﶶ﷌﷊ﶼ﷤
﷎ﶶﶸ﷌ﷂﶬ﷤
ﴶﴸﳰﴶﴸﳰﴸﴸ
Corresponding types of transmitters:
79)79$7'$7<*7<).7;7(;78
7&787&7=7=70=
ﶬﶰ﷒ﷂﶸ﷊ﶰ
，ＪＲＮＤ
Ｂ８Ｄ
ｄｂＮＤ
８＊＜＜
﷒﷎ﶬﵼﷂﶸﷄ
ﶬ﷊﷒﷎ﷄ﷊ﶰﵼﶮﶬﶪ﷌
﷤﷢ﵼ﷖ﵺ﷎ﷄ﷒ﶸﶸ﷊ﶼ
ﶮﶦﷂﶬ﷎ﷄ
ﴶﴸﴸﳜ
ﶺﶶ﷌﷊ﶼ﷤
﷎ﶶﶸ﷌ﷂﶬ﷤
ﴶﴸﳰﴶﴸﳰﴸﴸ